fix: CW speed drove the wrong keyer; survey the meters to find the SWR one

Speed: with DTR/RTS line keying the PC does the timing, so the Yaesu console's
slider — which sets the rig's internal keyer — changed nothing audible and looked
broken. Both entry points now go through one handler that drives the engine
actually sending, and additionally sets the rig's own keyer whenever a Yaesu is
on CAT, so the radio's front panel shows the same figure.

SWR: an operator reads 80 on the bar with a real SWR of 1.1. That is the shape of
reading the WRONG METER — ALC, say — not of a scaling error, and which RM index
carries which meter is not consistent across the family. Rather than guess again
and move the wrong number somewhere else, the first transmission now logs RM1
through RM6 raw, once. The log will say which index is which on this radio, and
the mapping can then be corrected as a fact.

changelog.json

@@ -3,6 +3,7 @@
     "version": "0.21.9",
     "date": "2026-07-28",
     "en": [
+      "CW speed is now one setting wherever you change it: the Yaesu console slider and the CW panel drive the keyer that is actually sending, and the rig own keyer follows so its front panel agrees.",
       "Antenna Genius: port A no longer jumps onto port B antenna a few seconds after a change. Only one port can hold the transmit antenna, so the switch reports the same one on both — the display now follows each port own receive antenna.",
       "CW through the Yaesu keyer: a fifth CW engine sends your macros with the radio own keyer (CAT \"KY\"), for the FTDX101 / FT-991A / FT-710 family. An FTDX10 does not accept it — DAKY included — and OpsLog says so, pointing to the serial DTR keyer on the rig second COM port, which works.",
       "CW through the Yaesu keyer: a fifth CW engine sends your macros with the radio own keyer (CAT \"KY\") — no WinKeyer, no second cable. Pick \"Yaesu (rig keyer)\" in Settings → CW keyer, with the Yaesu CAT backend active.",
@@ -19,6 +20,7 @@
       "CQ and ITU zones you correct by hand in your profile stay corrected. They are derived from cty.dat, which gives the zones of the whole entity — in a country spanning several, the automatic value is wrong and it came back at every restart. They now only fill in when empty, and recompute when the callsign or grid changes."
     ],
     "fr": [
+      "La vitesse CW est désormais un réglage unique où que vous la changiez : le curseur de la console Yaesu et le panneau CW pilotent le manipulateur qui émet réellement, et le keyer interne de la radio suit pour que sa façade affiche la même valeur.",
       "Antenna Genius : le port A ne bascule plus sur l'antenne du port B quelques secondes après un changement. Un seul port peut porter l'antenne d'émission, le switch renvoie donc la même sur les deux — l'affichage suit désormais l'antenne de réception propre à chaque port.",
       "CW par le keyer Yaesu : un cinquième moteur CW envoie vos macros avec le keyer de la radio (CAT « KY »), pour la famille FTDX101 / FT-991A / FT-710. Un FTDX10 ne l'accepte pas — DAKY compris — et OpsLog le dit en renvoyant vers le keyer série DTR sur son second port COM, qui fonctionne.",
       "CW par le keyer Yaesu : un cinquième moteur CW envoie vos macros avec le keyer de la radio (CAT « KY ») — sans WinKeyer ni second câble. À choisir dans Réglages → Keyer CW sous « Yaesu (keyer de la radio) », avec le backend CAT Yaesu actif.",