The sixth CW engine, and the one the TCI backend was left without. A SunSDR
keys from the WebSocket that already carries the CAT: no WinKeyer, no second
serial port, nothing to wire.
CW_MACROS:0,<text>; send
CW_MACROS_SPEED:<wpm>; speed
CW_MACROS_STOP; abort
Confirmed against the TCI command table in ars-ka0s/eesdr-tci — the source that
settled SPOT. CW_MACROS rather than TCI 2.0's CW_MSG: it exists from 1.6, and
OpsLog resolves its own variables, so the before/after callsign fields have
nothing to carry.
Commas and semicolons are stripped before sending. They are the protocol's own
separators: a comma would become another argument, a semicolon would end the
command with the message half keyed and the rest parsed as a command.
Only the MACRO speed is set, not the paddle keyer's — an operator who set their
paddle to 28 wpm did not ask for it to change because a macro went out at 25.
And there is no backspace: TCI can stop a message but cannot un-type one, so the
type-ahead correction the Flex engine offers is absent rather than faked.
TCI already carries the frequency, the mode, the meters and now the audio.
It also carries everything else about the radio — and OpsLog was logging
most of it once as '(unhandled once)' and throwing it away. The console is
mostly a place to put what was already arriving.
That makes it the cheapest panel here, and it is worth saying why. A K3
console costs a command and a reply for every value it shows, which is why
it reads its settings in a rotation and its meters only while on screen.
TCI PUSHES: the radio announces its drive, its filters, its noise blanker
and the rest on connect, and again whenever any of them changes —
including when the operator changes them in ExpertSDR3's own window, which
this panel therefore follows without asking anything.
What it drives: drive and tune drive, mic gain, TUNE, volume, mute,
squelch and its threshold, NB, NR, ANF, APF, AGC speed, the passband, RIT
and XIT with their offsets, and the VFO lock. The S-meter is a real dBm
reading, so its S units are arithmetic rather than the calibration guess a
K3's meter needs.
Setters never update the cached state. The radio answers with the new
value, and taking its word is what keeps the panel honest when a setting
is refused, clamped, or changed at the radio a second later — the one
exception being a slider mid-drag, held for 900 ms so it is not dragged
back by its own echo.
Capped width and centred, like the other consoles. Also offered as a
docked pane — and the Elecraft console is offered there too now: App has
always had that pane, Settings simply never listed it.
A SunSDR already carries its receive audio on the same WebSocket as its
commands, so a virtual audio cable and a second sound card are two pieces
of plumbing an operator installs for no reason. This is the receive half:
what the QSO recorder and the CW decoder need.
The reader now looks at the frame type. It used to ignore it and split
every frame on ';' -- harmless only for as long as no stream was ever
opened, since audio bytes would otherwise have been handed to the command
parser a hundred times a second.
NOTHING HERE IS CONFIRMED ON A RADIO. The header layout comes from the
TCI documentation, and the stream-type numbers are exactly the sort of
detail a document gets right and a memory of it does not -- so the first
forty frames of a session are logged verbatim, and a test bench in
Preferences > Audio reports the sample rate the radio chose, the frames
arriving and the peak level of the last second. 'The stream is open' and
'audio is arriving' are different claims and only the second is worth
anything to whoever tries this first.
Transmit (the voice keyer) is the other half and is deliberately absent:
it has to answer the radio's chrono packets at the right pace, and that
is worth doing once the format is settled on real hardware.
rouggy