OpsLog/wiki/Connections.md

Connections

Settings → Connections is where OpsLog talks to other programs and to hardware over the network: what it listens to, what it sends, and messages you write yourself.

It was called UDP until it grew a second transport — a row can now send an HTTP GET instead of a datagram, which is what most home-made antenna switches understand.

Each row has a name, a direction, a service type, a port, and an on/off switch. Everything sent and received is written to the application log, so a row that does not work can be diagnosed rather than guessed at — see Troubleshooting for where the log lives.

---

Inbound — what OpsLog listens to

Service	Sends it	Use
WSJT-X / JTDX / MSHV	those programs, port 2237	Log their QSOs automatically, follow the DX call being worked, and show their decodes. Multicast is normal here.
ADIF over UDP	JTAlert, GridTracker, FLDIGI	A text ADIF record per logged QSO.
N1MM Logger+	N1MM	Its XML contact record.
Remote callsign	DXHunter and similar	A callsign — and optionally a frequency and mode — to load into the entry form and tune to.

Multicast or unicast?

WSJT-X and MSHV normally broadcast to a multicast group (usually 239.255.0.1) so several programs can hear them at once. Tick Multicast and give the group. A program sending to one address only needs unicast — leave it unticked.

Do not put an inbound row and an outbound row on the same port. OpsLog then receives its own messages, and something it publishes can come back as a command. It says so in the log when it spots the arrangement: "X sends on port 2241 and Y listens on it — OpsLog will receive its own messages there; give one of the two another port."

---

Outbound — what OpsLog sends

Service	Format	Fires on
ADIF message	a plain ADIF record	each QSO logged
WSJT-X logged QSO	the same ADIF wrapped in a WSJT-X datagram	each QSO logged
PstRotator frequency	<PST><FREQUENCY>	frequency change
N1MM RadioInfo	N1MM's RadioInfo XML	frequency or mode change
Custom message	whatever you write	a trigger you pick

Which one for another logger?

If a logger says it accepts "WSJT-X UDP", it wants the WSJT-X logged QSO row — it listens on the WSJT-X interface and silently discards a bare ADIF record. Logger32 is the usual case. A logger that documents a plain ADIF listener wants the ADIF message row instead. They are two rows because they are two different things on the wire; enable the one your logger asks for, not both, or the QSO arrives twice.

---

Custom messages

The general case: you choose when it fires, what it says, and how it leaves. This is how a home-made antenna switch, a relay box or a home-automation server gets told what the station is doing.

1. Pick the trigger

Trigger	Fires when
QSO logged	a contact is saved
Band change	the radio changes band — or, on a station with no CAT, the Band selector in the entry strip
Rotator command	the antenna is told to turn (compass, SP/LP buttons, a spot click)
Lookup done	a callbook lookup returns

2. Write the message

Anything in {braces} is replaced. What is available depends on the trigger:

Trigger	Placeholders
QSO logged	{call} {band} {band_m} {mode} {grid} {name} {country} {rst_s} {rst_r} {comment} {date} {time} {freq_hz} {freq_mhz} {dxcc}
Band change	{band} {band_m} {mode} {freq_hz} {freq_mhz}
Rotator command	{az} {el} {path} (SP, LP or empty)
Lookup done	{call} {name} {grid} {country} {qth} {state} {dxcc}

{band} is 20m; {band_m} is just 20, because an antenna switch usually wants the number and nothing else.

3. Choose the transport

• UDP — a datagram to an address and port. You choose the line ending.
• URL — an HTTP GET. Values are URL-encoded automatically.

Examples

Turn an antenna switch on every band change, over HTTP:

Trigger:    Band change
Transport:  URL
URL:        http://192.168.1.50/set?band={band_m}

20 m → http://192.168.1.50/set?band=20

Tell a rotator display where the antenna is going:

Trigger:    Rotator command
Transport:  UDP  →  192.168.1.77:8100
Message:    <AZIMUT>{az}</AZIMUT><PATH>{path}</PATH>

Announce each QSO to a shack dashboard:

Trigger:    QSO logged
Transport:  URL
URL:        http://homeassistant.local:8123/api/webhook/qso?call={call}&band={band}&mode={mode}

Credentials in a URL are sent as typed — this is meant for a LAN. Passwords are redacted in the log so a log file can be shared safely.

When a band change is a band change

The Band-change trigger follows the radio, because an antenna switch should follow the radio and not what is being typed. Changing band in the entry strip drives the rig, the rig reports the new band, and the trigger fires from that.

On a station whose rig OpsLog does not control there is nothing to report back, so the Band selector itself counts as the band change. The 🔒 lock on Band or Frequency suppresses it: a lock means the entry is deliberately decoupled from the rig, and nothing should move for a contact logged from last year.

---

Diagnosing a row that does nothing

The log names every message. In order, check:

1. Is the row enabled? The list shows it.
2. udp: Reload done — N server(s) running at startup, and one cfg id=… name=… dir=… service=… port=… line per row. A row that failed to start is listed with its error.
3. Outbound: udp: [NAME] sent N bytes to ADDRESS (service) for a datagram, or the URL for an HTTP row.
4. A message that renders empty is skipped and the log says so — usually a placeholder that the trigger does not provide.
5. a QSO was logged but no outbound "ADIF message" row is enabled — the answer to "why does my other logger get nothing".

See also: Amplifiers and Switches for relay boards and their own automatic control, and DX Cluster and Spots for spot sources.