The seven minutes of reconnects in the operator's log turned out to be the radio
switched off — no defect. But the log said otherwise:
20:14:42 yaesu: ID query failed (timeout) — continuing…
20:14:44 yaesu: connected on COM7 @ 38400 baud, model="FTDX101D"
Opening the port was treated as connecting, and the model name was left over from
the previous session, so a powered-down rig produced a line claiming it was
connected as a named model. That is what sent me looking for a software fault.
Connect now tracks whether ANY probe answered. If none did, it clears the stale
model, says so in terms an operator can act on — is it powered on, is the CAT
rate right — and returns an error so the reconnect loop keeps trying rather than
believing it succeeded.
Connect assigned a fresh handle to y.port without closing the one it already
held. It is called again on every reconnect, so a rig that fails to answer leaks
one handle per attempt — every few seconds, indefinitely.
Windows opens a serial port EXCLUSIVELY, which makes this visible as "yaesu: open
COM7 @ 9600 baud: Serial port busy" in an operator's log: OpsLog was competing
with itself for the port.
This is a real defect found while reading the reconnect loop, but I want to be
straight about its limits: it does NOT explain the seven minutes of "ID query
failed — timeout" in the same log, where the port opened and the rig stayed
silent. That one is still open, and the operator alternates between two separate
radios (a TCI SDR and the Yaesu) rather than sharing one port, so a conflict
between backends is not the explanation either.
Reported both ways round, which is what settles it. With RX and TX on SUB
everything worked; with them on MAIN the frequency froze and a spot click tuned
the sub VFO. The log shows the rig answering FR01 in the MAIN case.
So on an FTDX101 the state is the FIRST digit — 0 = main — and the second is a
separate parameter. Yesterday I changed this to the LAST digit, which read FR01
as SUB and inverted the whole thing. The fault that change was meant to fix ("SUB
shows MAIN") came from reading VS instead of FR, and probing FR had already fixed
it on its own; the digit change was an unnecessary guess layered on a real fix.
Nothing else needed changing for the operator's two questions: the display and
SetFrequency already follow curVFO, so a spot now tunes whichever VFO holds RX
and TX, and the main frequency is read when on main. A test states that in those
terms — active VFO and which command a spot writes — rather than only as a byte,
because the byte is what I got wrong while believing the logic was right.
The log named the cause in one line: yaesu: receive VFO is read through FR
(answered "FR01;"). An FTDX10 answers "FR0;" — one digit — so reading the digit
straight after the prefix worked there and took the 0 of "01" on an FTDX101.
The rig was on SUB and OpsLog said MAIN, which is the reported "Sub shows the main
frequency". It also explains the second half: split is "TX VFO differs from RX
VFO", so a receive VFO that alternated between right and wrong made the split flag
flip between consecutive polls and swap freq and rx in the log.
The state is now taken from the LAST digit before the terminator, which is correct
on both forms, and the same reading applies to ST/FT/VS rather than leaving the
next two-digit rig to be found in the field.
On the operator's question of whether freq should simply be the active VFO: no —
freq is the TRANSMIT frequency by ADIF convention (FREQ is the QSO frequency,
FREQ_RX the receive one, set only when split). In simplex they are the same, so it
does read as the active VFO; in split it must stay the transmit VFO or the log
records the wrong frequency. What the operator saw was this bug, not that rule.
"Showing 10000 of 23683 matches · 28648 total" was read as a filter matching more
than the log holds. The numbers were right — 23 683 matches out of 28 648 QSOs,
capped at 10 000 displayed — but the middle one belonged to "matches" while
sitting where "of N" normally means the total.
Each number is now named where it appears: shown · match the filter · in the log.
Thousands separators too, since 23683 and 28648 are hard to compare at a glance.
No counting change: both counts run over the same table, so matches can never
exceed the total.
Reported: after a confirmation download they all turn to Y.
The test accepted qsl_rcvd = Y as a confirmation. That field is the operator's
OWN paper-QSL flag, which they uploaded to QRZ in the first place — so QRZ handed
it back and OpsLog read it as QRZ's answer. On a log full of paper cards that is
most of the log, which is exactly what was seen.
Only QRZ's own statement counts now: app_qrzlog_status = C, or the ADIF field
qrzcom_qso_download_status = Y that QRZ sets for it. LoTW and eQSL confirmations
are explicitly not accepted either — they are other services' answers, and the
column says QRZ.
This status feeds award slots, so a false Y is a QSO counted as confirmed when it
is not. That asymmetry is why the rule is narrow rather than generous, and the
test lists the negatives as deliberately as the positives.
The changelog warns that earlier downloads may already have set the column
wrongly — the fix stops it happening again but does not undo it.
Asked for as a missing feature. It is not missing — the "fill my station fields"
option has stamped the default QSL / LoTW / eQSL / Club Log / HRDLog / QRZ.com
statuses on empty fields since v0.14. What was missing is any mention of it: the
option's description talked only about MY_* fields, so the behaviour was
undiscoverable except by comparing a log before and after.
The description now says it, in both languages, and names why it matters — a
WSJT-X log carries almost no QSL fields.
The rule is also pinned by a test now, which meant splitting the fill from the
settings lookup: blanks are filled, existing values are never touched.
Overwriting them would erase confirmations the operator has actually received,
and that is the half a future edit is most likely to get wrong.
Describes what the operator gets: a spot click in DXHunter now moves the radio,
not just the callsign field. Notes explicitly that a packet without <FREQ>/<MODE>
behaves exactly as before — that is the reassurance anyone already using
remote_call needs, and it is the part a feature description usually omits.
Appended at the bottom of the block, per the rule adopted with 0.22.0: a version
is read top to bottom.
The operator's description separates the two cases precisely, and that is what
identifies the fault. RX alone on SUB displayed VFO B correctly; RX AND TX on
SUB — entirely on the sub receiver — displayed VFO A.
VS was being read as "which VFO is in use". On an FTDX101 it does not answer that
question: with both RX and TX on sub it still reported the main VFO. FR is the
command that selects the RECEIVE VFO, and it is now asked first, VS remaining the
fallback for models that lack it.
Split falls out of the same correction: split means the TRANSMIT VFO differs from
the RECEIVE one, so a wrong receive VFO made the comparison wrong too — which is
the second half of what was reported. A test covers all four RX/TX combinations,
including the one that is NOT split (both on sub) and reads as split if you take
the transmit VFO alone.
Translating the schema correctly does nothing for a database that already
exists. This operator's had been created by an earlier attempt, so qso.state was
already TEXT and every launch died on the same statement — CREATE INDEX … ON
qso(state), error 1170 — with the connection failing at startup and no way
forward from the UI.
Columns that MUST be VARCHAR (the indexed and keyed ones) are now converted
before the migrations run. It reads information_schema, touches only the columns
in varcharColumns, and only when they are actually TEXT — a no-op on a healthy
database, and it preserves each column's NULL/NOT NULL.
A failure to repair IS reported: it is the difference between a logbook that
opens and one that does not. A failure to READ information_schema is not — a
server that will not answer it can still be running a perfectly good schema, and
refusing to open would turn a non-problem into an outage.
The quoting fix was necessary but not sufficient: "column 'op_name' can't have a
default value" persisted.
The translation worked line by line and rewrote only the FIRST column on each
line. Our own migrations put one column per line, so nothing showed there — but
sqlite_master stores a table's CREATE statement with every ALTER-added column
appended to the SAME line, and the baseline is built from exactly that. On a
logbook that had been through upgrades, most columns therefore kept their TEXT
type and MySQL rejected the schema.
Two consequences fixed together: every match is now rewritten, and each one is
decided from ITS OWN declaration — the text between the surrounding commas —
rather than from the whole line. Deciding per line would have made every column
sharing a line with a default-bearing one into VARCHAR(255), which breaches the
InnoDB row-size limit the TEXT rule exists to respect.
Tests cover the many-columns-on-one-line shape and pin that a neighbour's DEFAULT
does not leak.
Two errors from a shared MySQL logbook, both fatal to the schema and neither
naming its cause:
CREATE INDEX … ON qso(state) → 1170 BLOB/TEXT column used in key
specification without a key length
op_name TEXT … DEFAULT '' → 1101 TEXT column can't have a default value
One root cause. TEXT columns are rewritten to VARCHAR(255) when they are indexed
or carry a default — that is exactly what those two MySQL rules require — but the
pattern only matched a BARE column name. The SQLite baseline dump quotes its
identifiers, and mysqlDDL turns those quotes into backticks before the TEXT rules
run, so every column coming from the baseline kept its TEXT type and MySQL
rejected the schema.
The operator saw none of this: just "MySQL is enabled but the connection failed
at startup" and a silent fallback to local SQLite — which is the worst shape for
a shared logbook, because each operator then logs into their own copy.
The pattern now accepts a quoted or bare name and puts the quoting back. A test
covers both forms, plus the case that must NOT change: an unindexed column stays
TEXT, since VARCHAR everywhere would break MySQL's row-size limit. Reverting the
one-line change makes it fail.
Reported on an FTDX101: the panel showed split ON with the radio OFF, and the
reverse — while the same model behaved correctly for another operator, and an
FTDX10 was fine throughout. That pattern is the clue: one operator was on MAIN,
the other on SUB.
The two commands say different things and were read alike:
ST is a split FLAG — ST1 means split, whatever VFO is in use.
FT names the TX VFO — FT0 = transmit on A, FT1 = transmit on B.
Split is on when the rig transmits on a DIFFERENT VFO from the one it listens to.
Reading FT1 as "split" is therefore correct only on VFO A, and exactly inverted
on SUB. It is now compared with the current VFO.
Writing had the identical fault, and it was worse: sending FT1 for "split on"
while the operator listened on SUB CLEARED the split it was asked to set. Both
directions are pinned by tests over each VFO state.
Reported on an FTDX101 (F4NBZ): listening on the SUB VFO, clicking a spot moved
the radio to MAIN.
SetSimplexMode is the first thing SetFrequency tries, and it means "receive and
transmit here, simplex" — OmniRig applies that to the MAIN VFO by definition. It
is there because several Icoms ignore direct FreqA/FreqB writes, so it stays for
the main VFO; on SUB it is now skipped entirely and FreqB carries the change.
The generic "Freq" property is skipped on SUB too: on several rig files it IS the
main VFO, so writing it would move the VFO the operator is not using — or pull
them back to it, which is the bug being fixed.
An operator on SUB put themselves there deliberately. A spot click asks for a
frequency, not for a change of VFO — that distinction is the whole fix, and a
test pins which property each VFO state writes.
Reported with screenshots: a dozen records lifted out of wsjtx_log.adi into a new
.adi imported as "0 imported, 0 ignored, 0 total". The parser only emitted
records after <EOH>, and a hand-assembled file has no header — so the whole file
was read as header text and thrown away. The count says the file was empty; there
is nothing on screen to suggest a missing tag, which is why this was reported as
"import does nothing".
An <eor> is proof that a record ended, header or no header. Fields are now
collected always and DISCARDED at <eoh> — that tag is exactly the statement
"everything before this was the header", so real headers stay out of the data
just as reliably, and a headerless file keeps its first record instead of losing
it to the same rule.
An existing test asserted the old behaviour. It encoded a defensible reading of
the spec, but the file it rejects is one operators really make and the rejection
is silent, so the test is rewritten with the evidence that changed it rather than
deleted.
New entries were being prepended, so a version block read backwards: an operator
met "the Yaesu meters are corrected" and "the console follows the mode" several
entries before learning that a Yaesu console existed. The fixes made sense only
to someone who had followed the development.
0.22.0 is reordered so each feature appears before what was fixed on it, and
CLAUDE.md now says to append at the bottom.
Restored the entry that INTRODUCES the Yaesu console: I had overwritten it when
editing the meters entry in place, so the release described corrections to a
panel it never announced.
The byte trace from a real WK2 settled in one line what no amount of reading
could: "TX 11 32". Command 0x11 is SET KEY COMPENSATION in milliseconds, not the
dit/dah ratio — that is 0x17. So a neutral ratio of 50 asked for 50 ms of extra
key-down on EVERY element. At 25 wpm a dit is 48 ms, so elements more than
doubled and ran into each other: the reported "it sends one element, then a long
pause".
The ratio now goes out as 0x17, and the compensation is explicitly set to 0 —
merely stopping the wrong command would leave an affected keyer misbehaving,
since it keeps the value in EEPROM until something writes over it.
The init sequence is now built by a separate function so the BYTES are testable,
and a test pins each command number. These numbers are the contract with the
hardware, and a wrong one produces a fault that cannot be diagnosed from the UI
at all — this one cost the operator weeks and needed a trace to find.
This is why the fix waited for the trace rather than being guessed: the plausible
guesses (mode register, sidetone, WK1-vs-WK2 differences) were all wrong, and any
of them shipped blind would have broken the keyers that work today.
Renamed from 0.21.9 at the author's request: this release adds native Yaesu and
Xiegu CAT, CAT sharing over Hamlib NET rigctl, a Yaesu console and a fifth CW
engine, which is a minor version rather than a patch.
The Yaesu keyer had two entries — one written when it was added, one when the
FTDX10 turned out to refuse it. Merged into the single statement an operator
needs: what it does, where to select it, and which rigs accept it.
The weak audio was not a level at all: the radio was still modulating from its
front microphone, so almost nothing of the USB feed reached the air. On an FTDX10
that is MENU → SSB MOD SOURCE = REAR.
Worth putting in the settings hint rather than leaving in a conversation — every
operator wiring a voice keyer for the first time meets it, and no amount of gain
in OpsLog can compensate for a rig listening to the wrong input.
The messages went to the radio exactly as recorded. Nothing in OpsLog could
raise them, so a microphone captured quietly drove the rig quietly and the only
remedies were the radio's own USB input menu or the Windows mixer — which is
where the operator was heading. There is now a level from 10 to 400 %, applied
with clamping (a wrap would turn loud speech into noise on the air), and Play
previews at that same level so the adjustment is made against what will actually
be transmitted.
The PTT method list also named only OmniRig, Flex, Icom and TCI, so choosing a
native Yaesu left "CAT" with no backend beside it — which reads as "there is no
CAT PTT for my radio" and sends the operator to RTS on a COM port that has
nothing to do with the rig. Same list-needing-every-member shape as three
earlier bugs in this feature. The TestPTT log line had the same rot: it said
"CAT via OmniRig" whatever backend was running.
Receiving cleared the two bar percentages but not the values the bars now
actually draw from: the watts and the SWR ratio, added when the meters were
corrected. So the power bar sat pinned across the panel with the rig plainly
receiving — the dash in the label said one thing and the bar another.
Every transmit value is cleared now, and the peak-hold state with them: a peak
left in the holder would have carried the last transmission's reading into the
start of the next one, which is worse, being wrong while it looks live.
The panel also draws both bars from zero unless the rig reports transmitting, so
a value that has not been refreshed yet cannot show as output.
One point could not reveal the curve. Scaling 207 = 100 W straight down read
30 W where the radio showed 10, and 75 where it showed 50 — wrong everywhere
except at the single point it was fitted to.
Three readings taken against the rig's own display give the shape:
raw 62 → 10 W
raw 155 → 50 W
raw 207 → 100 W
Interpolating between them reproduces the radio exactly at those points and stays
close in between. I did not fit a formula: three samples can be made to support
several curves, and the operator can check a table against their own meter.
Above the top the last segment's slope continues rather than clamping, so a rig
driving an amplifier does not sit pinned at 100 W. A test pins the measured pairs
and the monotonicity, so a later change that breaks them fails against the radio
rather than against taste.
A quarter-per-poll decay covers the milliseconds between CW elements but not the
gaps that matter on the air: between the words of a CQ, in CW as in SSB, the
meters genuinely read 0 for most of a second and the bars fell with them.
A peak now stands for 1.5 s before it starts to fall, and still rises instantly —
a needle goes up fast and comes down slow. The SWR RATIO is not updated at all
from a zero reading: showing 1.0 during a word gap is worse than showing a stale
figure, because it looks like good news.
A test caught a real defect on the way: the proportional decay stalls on
integers. With the needle at 13 and the truth at 10, a quarter of the gap rounds
to zero and the meter sat three units high for ever. It now always steps down by
at least one, so it converges.
An FM carrier could not answer it: constant by definition, so nothing to
correlate. CW at 100 W did, because the keying itself varies the output:
key down: RM4=25 RM5=207 RM6=13
key up: RM4=25 RM5=0 RM6=0
RM5 follows the RF envelope exactly — it IS the power meter. RM4 sits near 25
whether the key is down or up, so it is not measuring output at all, and reading
it as power is what showed 8 W on a 100 W transmission. The operator's hunch was
right and my first reading of the ramp was wrong: what I took for a needle
rising was RM4 drifting, not tracking.
Watts are now derived from that meter (207 = 100 W, measured) instead of the
power SETTING scaled by a percentage — the setting says what was asked for, the
meter says what left the radio.
The bars also hold their peak with a gentle decay. In CW the meters genuinely
read zero between elements, so following the raw value made them flash to nothing
several times a second; a needle has inertia, and this only ever holds a value
the radio really reported.
One transmission cannot name it. RM4 rose while RM5 stayed flat — which points at
RM4 — but RM5 differed BETWEEN transmissions, 208 then 105, which points at RM5.
Both readings are consistent with either answer, so picking one now would just be
the FT-991A table mistake again in a new place.
The survey line now carries the rig's power setting, and the sample cap is raised
from 12 to 40 so two transmissions fit. Keying at, say, 10 W and then 100 W makes
the answer a one-line comparison: the wattmeter is whichever index moves with the
setting.
The displayed mapping is left alone until that comparison exists.
A second measurement at a known mismatch settled both the index and the scale.
At SWR 1.1: RM6=0. At SWR 1.5: RM6=52, while RM4 kept tracking the power.
52/255 = 0.204, which is the reflection coefficient of a 1.5 SWR to three
decimals. So the raw value is rho scaled to 255, and the ratio is
(1+rho)/(1-rho) — physics, not a curve fitted through two points, which is why
2.0 and 3.0 fall out of it correctly without ever having been measured.
The panel now shows that ratio, the number the operator reads on the rig, rather
than a percentage of meter travel — and a dash while receiving, since a stale SWR
from the last transmission reads as a live one.
Both measurements are recorded in the code and in a test, so the mapping is
evidence rather than a table borrowed from another model — which is exactly how
it came to read 81 in the first place.
Measured on the radio, steady carrier for three seconds:
RM1=0 RM2=unsupported RM3=0 RM4=9→18→21→22 RM5=208 flat RM6=0
RM4 is the index that RAMPS with the output, so RM4 is the power meter. RM5 sat
at 208 from the first sample to the last, unmoved by the power — that is not SWR
on an operator reading 1.1, and 208/255 is exactly the 81 that appeared on the
bar. Borrowing the FT-991A's table, which puts SWR on RM5, is what put it there.
SWR now reads RM6. It stayed at 0 throughout, which is CONSISTENT with a 1.1
match but does not prove the index — only a deliberate mismatch would, and I am
not asking for that. A bar at zero on a good antenna is honest; 81 was actively
misleading.
The measurement is written into the code next to the mapping, so the next person
sees the evidence rather than a table copied from another model.
The one-shot survey fired as the transmission began and caught the meters still
at rest — RM4=13 and everything else zero, which identifies nothing. And the
operator's reading points the other way: the bar showing 81 tracks his 100 W,
while the one labelled power sat at 8.
What names a meter is which index FOLLOWS the power over a few seconds of steady
carrier, so the survey now samples on every poll while transmitting, capped at a
dozen lines. Two seconds of tune will settle it.
Still not guessing at the mapping: the numbers will say which index is power and
which is SWR on this radio, and it gets corrected then.
Speed: with DTR/RTS line keying the PC does the timing, so the Yaesu console's
slider — which sets the rig's internal keyer — changed nothing audible and looked
broken. Both entry points now go through one handler that drives the engine
actually sending, and additionally sets the rig's own keyer whenever a Yaesu is
on CAT, so the radio's front panel shows the same figure.
SWR: an operator reads 80 on the bar with a real SWR of 1.1. That is the shape of
reading the WRONG METER — ALC, say — not of a scaling error, and which RM index
carries which meter is not consistent across the family. Rather than guess again
and move the wrong number somewhere else, the first transmission now logs RM1
through RM6 raw, once. The log will say which index is which on this radio, and
the mapping can then be corrected as a fact.
Tested on the radio: DAKY does not help, KY is refused whatever PC KEYING is set
to, and the "Serial port (DTR=CW / RTS=PTT)" engine on the second COM port keys
correctly. So my earlier "try DAKY first" was wrong, and the order is now the
other way round: name what works, mention the model that refuses.
The KY engine stays. It is documented for the FTDX101 / FT-991A / FT-710 family
and costs nothing to keep — a rig that refuses it now says so in one clear
sentence instead of transmitting nothing for no stated reason.
The operator found the menu I said to look for: it offers DAKY, RTS and DTR. KY
is the CAT route, so DAKY is the setting that would enable it — which makes my
previous "this rig has no CAT keying command" too strong a claim to leave
standing, since it was drawn from a refusal at the DEFAULT setting.
The error and the settings hint now name DAKY first, and keep the serial line
keyer as the fallback. That order matters: the CAT route costs nothing, the
fallback costs a second COM port.
Marked as untested rather than verified — I have no confirmation that DAKY makes
KY work on this model, only that it is the option that should.
Confirmed on the radio: it answers "?;" to KY, so this is not a setting to find.
My previous message sent the operator looking for a MENU → CW → PC KEYING entry I
named without checking it exists on that model, and they could not find it.
The message now names the path that does work: the "Serial port (DTR=CW /
RTS=PTT)" keyer on the rig's OTHER COM port — the standard one — while CAT keeps
the enhanced one. Same for the settings hint and the changelog.
The KY engine stays: it is documented for the FTDX101 / FT-991A / FT-710 family.
It now fails loudly and usefully on the models that lack it, which is the
difference between a dead feature and a wrong one.
The log timed it exactly: the CW send at 13:16:17.591, the CAT dropping at
13:16:17.633, forty milliseconds later.
An accepted KY says nothing, but a REJECTED one answers "?;" — and nobody was
reading it. The frame sat in the buffer until the poll loop's next query picked
it up, failed, and the Manager tore the link down. That is the disconnect on
every macro click, and it also explains the silence: the backend was being
rebuilt underneath the send.
Two changes. The KY write is now followed by a short read: silence means
accepted, "?;" means refused — and the operator is told so, naming MENU → CW →
PC KEYING, instead of getting nothing with no reason. And FA; retries once when
it meets a stray rejection, because a "?;" arriving there is almost never about
FA: the rig answers frequency queries perfectly well, it is the previous
command's refusal being attributed to this one.
This does not yet prove the FTDX10 accepts KY at all. It makes the next run say
so plainly either way, which is the point.
The log settled it: the rig answers "?;" — its "unknown command" — to KY; and to
MG;. So the keyer status query cannot work on this model, and every send spent
four seconds waiting for an answer that was never coming.
"?;" is now recognised as what it is. A command refused once is never asked
again: models implement different subsets, and re-asking costs a 600 ms timeout
on every slow beat for a control that will never answer — which is also why the
panel felt sluggish.
Without a buffer status there is still a real constraint: one KY command carries
24 characters and the rig DROPS the rest silently. So the send is now paced by
how long the text takes to key, from PARIS timing at the rig's own speed. A long
macro goes out complete instead of losing its tail.
That leaves the question the log cannot answer: whether KY <text>; itself is
accepted. If the rig also replies "?;" to it, the CAT menu's PC KEYING setting is
the next suspect — but nothing in the code will be guessing at it.
Clicking a macro dropped the CAT for a few seconds, keyed nothing, then came
back.
ask() returned the first ';'-terminated frame it saw, whatever command it
belonged to. KY produces NO reply, so the next query — FA; from the poll loop —
collected a leftover frame, failed to parse it as a frequency, and ReadState
reported an error. The Manager reads that as "lost the rig": disconnect, wait,
reconnect. Hence the drop and the automatic recovery a few seconds later.
Replies are now matched to the command that asked for them: anything else is
discarded and logged, so a stray frame costs one log line instead of the link.
This also explains the silence — the send never got a clean run at the port
while the backend was being torn down under it.
"the keyer buffer stayed full for 4s" and nothing keyed, on a rig whose CAT is
working. The buffer was not full: the check demanded the reply be exactly "KY0;"
with the digit at byte 2, so anything the FTDX10 phrases differently — a space
before the digit, another command's reply arriving first — read as "still full"
on every poll until the deadline.
The test is now asymmetric on purpose: only a clear "1" holds the send back.
Anything unrecognised goes ahead. Refusing to transmit because a status line was
phrased unexpectedly is the worse failure — the operator gets silence with no
explanation, where at worst sending early truncates a long message, which the
chunk loop then recovers from.
The reply is also logged once per run, since we have no verified sample of it —
that line is what turns the next surprise into a fact instead of a theory.
Three places decide what a rig keyer is, and the Yaesu was only in two of them.
The CW panel's status came from a list naming icom and flex; anything else fell
back to the WinKeyer status, which reports disconnected because no WinKeyer is
attached. So the panel said the rig CAT was offline while the console beside it
was reading the FTDX10 perfectly.
The send loop had the same gap: a rig keyer BUFFERS the whole message, so the
wait before <LOGQSO> is a length estimate, while WinKeyer watches a busy echo
that will never arrive here. Auto-call would have raced the transmission.
This is the third time the same shape has bitten in this feature — a list of
engines that needs every member named, with a silent fallback for the rest.
Grepping for the pair "icom || flex" is what finds them.
Choosing "Yaesu (rig keyer)" saved correctly and still produced a WinKeyer panel
asking for a COM port. The engine is normalised on load through a chain that
names icom, flex and serial and maps EVERYTHING ELSE to "winkeyer" — so the
value came back as WinKeyer on every read, whatever the settings said.
That is why the panel offered COM3 then COM10: it genuinely believed the engine
was a WinKeyer. The list now names yaesu too.
The same shape of bug is worth watching for: a normaliser with a silent default
turns an unknown value into a plausible one instead of an error, and the symptom
appears far from the cause — here, in a panel three components away from the
setting.
Selecting the Yaesu keyer fell through to the WinKeyer branch of the settings,
which offers a serial port picker and a Connect button. So the operator went
hunting for the right port — trying the standard COM and the enhanced one in turn
— and neither connected, because this keyer uses NEITHER: it keys over the CAT
link already configured in Settings → CAT.
It now has its own branch, like the Flex one: a speed field, the warning when the
CAT backend is not a Yaesu, and a line saying explicitly that keying rides the
CAT link. Speed changes go to the rig's keyer instead of a WinKeyer that is not
there.
Reported on an 8x2: port A correctly on the 80 m vertical, then a few seconds
later both A and B shown on the same beam.
The display preferred the TX antenna, falling back to RX. On an 8x2 only ONE port
can hold the transmit antenna, so the switch reports the same txant on both — and
every keepalive poll redrew port A as whatever port B transmits through. The RX
antenna is the per-port selection, and the only thing Activate sets, so it is
what a port shows; TX stays the fallback for a port reporting no RX antenna.
A port change is now logged with the raw line — but only on CHANGE, since the
device pushes state every few seconds and logging each one would bury the rest.
Without any trace, "port A jumped to the wrong antenna" cannot be checked.
Two tests pin it: rx wins over a disagreeing tx, and a message about one port
never moves the other — which is the shape that was actually on screen.
The radio has a keyer and a command to feed it (KY), so an FTDX10 needs no
WinKeyer and no second cable, exactly as the Icom CI-V and Flex CWX engines
already do. The rig keys with its own timing, which is why the spacing is right
where a PC keying a line through USB latency drifts.
Text is filtered to what the keyer can actually send: an unsupported byte does
not produce an error on a Yaesu, it can abort the whole buffer, so the rest of a
macro would vanish silently. It is then fed in 24-character pieces, waiting for
room between them — the rig DROPS what does not fit, again with no error, so a
contest CQ would lose its tail.
STOP is the honest gap. Yaesu documents no buffer-clear, so it drops the
transmitter (TX0) instead: nothing queued reaches the air, which is what Escape
means to an operator. It deliberately does NOT send "KY0;" — a plausible-looking
clear that the rig would read as the CHARACTER zero and transmit.
A test caught a real one on the way: tabs and newlines were dropped as
"unsupported", gluing the words either side together, so a macro written on two
lines went out as CQCQ. Whitespace now becomes a word gap before filtering.
Settings warn when the Yaesu keyer is selected without the Yaesu CAT backend —
otherwise it simply never keys, with nothing on screen saying why.
Send path follows the CAT reference and how Hamlib drives these rigs; NOT yet
verified on the air.
Confirmed on the FTDX10: receiving on 14.018.98 and pressing SPLIT put 14.019.98
in the big display with "TX 14.019.98 (0 kHz)" under it. The radio was right —
RX 14.018.98, TX 14.019.98, up 1 kHz on CW — the panel was not.
RigState follows the ADIF convention where freq_hz is the TRANSMIT frequency, so
under split it is the OTHER VFO. Taking it as the main display showed the
operator the frequency they transmit on, and then an offset of that frequency
against itself: zero.
The header now reads the listening frequency (freq_rx_hz when split, freq_hz
otherwise) and the TX line shows the real transmit frequency and offset.
Microphone gain and VOX are meaningless in CW: the rig ignores both, so showing
them is showing dead controls. They are hidden, and a CW card takes their place
with keyer speed (KS), break-in (BI) and ZIN (ZI), the zero-in that retunes so
the station being received lands on the operator's own pitch.
ZIN is a one-shot with no state, so it is a plain button rather than a chip that
would look latched, and no settings read-back follows — the frequency change
arrives through the normal poll like any other.
The keyer values are read on the slow beat whatever the mode, so the card is
already populated the instant the operator switches to CW instead of filling in a
poll cycle later.
Which controls show is decided by the RIG's mode, not the logged one: the logged
mode can be a digital sub-mode the radio knows nothing about.
The bar was one colour for its whole travel, so nothing distinguished a signal
that is merely readable from one that belongs in the log as 59+20.
Green to S9, amber through the S9+ range, red from +20 dB. The thresholds are
computed from the SAME S9 point the label uses rather than hard-coded
percentages: the S9 position is still a hypothesis on this rig, and when it is
corrected the colours have to move with it or the meter would say 59+20 in
amber.
Reported on the FTDX10: listening on 14.244 with VFO B still holding 18.115 from
an earlier session, pressing SPLIT threw the transmitter onto another band. The
button only flipped the rig's split flag, and the other VFO is stale by nature —
the only transmit frequency that makes sense is one derived from where the
operator is listening NOW. SPLIT therefore places the TX VFO too: up 1 kHz on CW
and the data modes, up 5 kHz on phone, the offsets operators actually call. The
+1k / +5k buttons remain for anything else, and a test pins the mapping.
The panel also drew its own flat meters while the Flex and Icom consoles use the
shared LED-segment MeterBar. Two instrument styles in one application is just
inconsistency — it now uses the shared component, and the local one is gone.
And the three consoles are named alike: "Flex Console", "Icom Console", "Yaesu
Console", in the tabs and in the Main-view pane list, in both languages.
Three corrections from the operator's second pass.
The sideband gesture was wrong: I used double-click, which hides the action.
Clicking a button that is ALREADY active now flips its sideband — CW-U → CW-L →
CW-U. One button, one finger, nothing to discover.
A lit SPLIT chip does not tell an operator anything useful: it says split is on,
not where they transmit. The header now shows the TX frequency and the offset in
kHz whenever split is active.
And the offset that matters is set in one action: up 1 kHz on CW, up 5 kHz on
phone. Doing it by hand means swapping VFOs, retuning and swapping back — exactly
the fumbling a panel exists to remove. Both are offered rather than picked from
the mode, because which one is idiomatic is the operator's call, and the button
turns split on at the same time.
The offset is measured from the RECEIVE frequency and written to the VFO we are
not listening on, so it stays correct when the operator works on VFO B, where the
roles are mirrored.
Capping the width without mx-auto pinned the console to the left edge with an
empty window beside it. It now uses the exact wrapper the other two panels use —
h-full min-h-0 overflow-auto bg-background, then max-w-5xl mx-auto p-3 — rather
than a second layout of my own invention.
First look on the FTDX10 turned up six things:
The S meter printed a raw percentage — "57" tells an operator nothing, and it is
the S number that goes into a report. It now reads S1-S9/S9+dB, the same value
the click-to-fill RST already used.
CW, RTTY and the data modes exist on BOTH sidebands and the operator is the one
who knows which they want. The buttons now carry the rig's actual sideband and a
double-click flips it; PSK is added, riding the rig's DATA mode as it does on the
radio itself. This also means the mode row drives the rig directly (MD0 with the
exact mode) instead of going through the ADIF path, which could only pick a
sideband by convention.
The attenuator is a 6/12/18 dB pad on these rigs, not the single step I assumed —
two thirds of the control was unreachable.
Sliders had no visible filled side: --muted is barely lighter than the card it
sits on, so the whole track read as one bar. They also came in three kinds (two
bare range inputs among them). One component now, explicit track colour, and it
takes a min/max so power in watts and DNR 1-15 look like the rest.
The panel stretched across the whole window; it is a column of controls, so it is
now capped and every row stays readable.
And it gets its own Yaesu tab, like FlexRadio and Icom, rather than only being
available as a Main-view pane.
A console pane for the native Yaesu backend, in the same shape as the Icom and
Flex ones: S/PO/SWR meters, band and mode rows, AF/RF/squelch, AGC, the IPO/AMP1/
AMP2 front-end selector, ATT, NB, DNR + level, narrow filter, power in watts, mic
gain, VOX, split and ATU tune.
Three decisions worth keeping:
Panel reads are STAGGERED and live in their own file, away from ReadState. Meters
poll every cycle; settings only change when someone turns a knob, so they refresh
every 8th cycle and right after any set. Polling all of it every cycle would put
twenty queries a second on the serial link the frequency display shares.
Band buttons use the rig's own band memory (BS) rather than a frequency we pick,
so 20 m lands where the operator last was on 20 m — what the radio's own band
keys do.
A set is followed by a read-back, so the panel shows what the RIG ended up with,
not what we asked for; the two differ whenever a value is out of range or the
mode forbids the control. And a control the model lacks keeps its previous value
instead of dropping to zero, which reads as a setting that reset itself.
The S9 point of the S-meter scale is a hypothesis (the manual does not state it)
and is commented as such — one number to correct if reports come out an S unit
off, rather than a fudge spread through the RST helper.
Also removes the FlexRadio settings blurb, which explained the backend to
someone who had already chosen it.
Xiegu speaks CI-V with a reduced command set: frames, BCD encoding, addressing
and the opcodes for frequency, mode, PTT and split are Icom's, so this reuses
internal/cat/civ wholesale instead of re-deriving a codec.
It is a SEPARATE backend rather than the Icom one at address 0x70, because what
the two rigs do NOT share is the deciding part. The Icom backend reads the
spectrum scope, the DSP block, data mode via 1A 06 and the model id via 19 —
none of which a Xiegu implements. Pointed at a G90 it would poll every cycle for
answers that never come, and spend its silence tolerance on commands the radio
was never going to support.
Two consequences of the rig's smaller mode table are handled explicitly rather
than left to fail: there is no data mode, so a digital QSO is set to plain
sideband (what the operator does on the radio anyway) instead of being refused;
and the split TX frequency is NOT reported, because reading the unselected VFO
needs 0x25, which the Xiegu table does not list — a split flag carrying a wrong
TX frequency is worse than the flag alone, since the frequency is what gets
logged.
The published command table has rows that slipped during typesetting (0x07 and
0x0F share a block). Where it contradicts itself the Icom meaning is used, the
rest of the table matching Icom exactly, and every unexpected reply is logged
raw so a first on-air run settles it.
NOT yet verified on a radio.
MSHV worked immediately, JTDX answered "Hamlib error: Invalid parameter while
setting frequency". The two use different Hamlib dialects: MSHV sends
"F 14074000", JTDX names the target first — "F VFOA 14074000". The VFO name
landed in the slot the frequency was read from, the parse failed, and we returned
RPRT -1, which is exactly the error JTDX reported.
A leading VFO name is now stripped from every command's arguments. It costs
nothing: OpsLog follows the rig's own VFO selection, so the name carries no
information we act on — but refusing it locked out a whole family of clients.
Both dialects are covered by a test, the plain one included, since this is an
addition and must not become a swap.
A rejected frequency is also logged with the raw line now. The client only shows
"Invalid parameter", which says nothing about what it actually sent — that is
why this took a screenshot to diagnose rather than a log.
A native CAT backend owns the rig's serial port, and Windows gives a COM port to
one process — so choosing native CAT locked WSJT-X, MSHV and JTDX out of the
radio entirely. That is the cost of dropping OmniRig, which was itself a sharing
layer, and it has to be paid back.
OpsLog now becomes the server, as wfview does. It speaks the Hamlib net rigctl
protocol, which every one of those programs supports natively (rig model "Hamlib
NET rigctl", 127.0.0.1:4532) with no driver to install. It sits in front of the
MANAGER, not a backend, so an operator on OmniRig, Flex, Icom or TCI gets the
same server.
Two details that decide whether a client works at all rather than degrading:
dump_state is parsed positionally and WSJT-X refuses to proceed without a
well-formed block, so it is written out in full and its shape is pinned by a
test; and set_vfo / set_split_vfo answer RPRT 0 rather than an error, because
OpsLog follows the rig's own VFO and a refusal makes WSJT-X abandon the
connection. Unknown commands answer RPRT -11 — never silence, which hangs a
client instead.
The whole protocol is tested against a fake rig, plus one end-to-end exchange
over a real socket, since the framing is as much the contract as the text.
Also: the Yaesu backend is confirmed working on a real FTDX10 (frequency, mode,
VFO, split), so its "not yet verified" note is now wrong and is corrected.
Every Yaesu fault reported so far came from OmniRig's interpretation layer, not
from the radio: a rig file that never exposes the VFO, a Freq property meaning A
on one model and B on another, a split flag that alternates between polls. This
talks to the rig directly, so what the radio answers is what is shown.
Modern Yaesu CAT is plain ASCII with a ';' terminator — FA/FB for the VFOs, MD0
for the mode, VS for the selected VFO, TX to key. Frequency is written to the VFO
the operator is actually on, not always to A, which is the failure that made a
display disagree with the radio.
Two things are genuinely uncertain across the family and are treated as such
rather than guessed. SPLIT is read through ST, then FT if the rig ignores ST —
whichever answers wins and the choice is remembered, because the two commands say
DIFFERENT things (a split flag vs which VFO transmits). If neither answers, split
is reported OFF and the fact is logged, rather than invented. Unknown model ids
and mode bytes are logged raw for the same reason.
Split resolution, frequency parsing and the mode mapping are pure functions with
a table test — the OmniRig equivalent is where every Yaesu bug lived, and it had
no test until late.
Written from the CAT reference; NOT yet verified on a radio.
The log settled it: the backend was right all along. Every set produced
"readback +1.5s FreqA=21140000 Freq=21140000 -> shown 21140000" and published
cat:state with the new frequency and band. The display did not follow.
The fault is in the frontend. Changing band does two things at once: it opens the
1.5 s freeze that protects what the operator is typing, and it commands the rig.
The rig's answer comes back in ~170 ms — inside that freeze — and the handler
DROPPED any snapshot arriving during it. The backend only emits on change, so
nothing came afterwards, and the strip kept the old frequency until the VFO was
nudged. Changing band from the radio always worked because no freeze was open.
A dropped snapshot is now kept and replayed when the freeze closes, rather than
discarded. Further typing simply defers the replay again.
An import that drops the locator leaves it missing on a whole batch, and fixing
that one QSO at a time is exactly what bulk edit exists to avoid.
Added on all three sides in lockstep — the dialog field, the field-to-column map,
and the repository whitelist — because they are separate lists and offering a
field the repository refuses fails only at Apply, after the operator has selected
the QSOs. The existing contract test covers it.
The callsign and RST stay excluded, as before: bulk-setting those corrupts a log.
The locator does not carry that risk — it identifies a place, not a station, and
a wrong value is simply overwritten again.
An operator reports that "QRZ.com received status = N" returns rows showing both
N and Y (issue #5 follow-up). The SQL is a plain col = ?, but reading it cannot
distinguish a wrong query from a UI that kept the previous rows after an error —
so this runs it: five QSOs inserted, filtered, and both the list and the count
asserted. The backend filters correctly, list and count agree. The fault is not
in the query.
Found while looking: the filter builder tested an ADIF date with /^d{8}$/ instead
of /^\d{8}$/. The escape was missing, so the branch never matched and the
calendar input was handed "20260728", which type=date rejects — an empty box
over a value that was really stored.
Adds the IC-7300MKII at CI-V 0xB6.
Doing so exposed a drift between the two hand-kept copies of the model table: the
settings offered the IC-7700 at 0x88 and the IC-7800 at 0x80, which are the
IC-7100's and the IC-7410's factory addresses. Picking either set an address the
rig never answers on — the symptom is a radio that simply stays silent — and the
backend then named it as the other model. Corrected to 0x74 and 0x6A, and the
four models the backend already knew (IC-7100, IC-7410, IC-7600, IC-7851) are now
offered too instead of forcing a manual address.
A test reads the model list out of the .tsx and asserts civ.ModelName agrees, so
the next model added on one side alone fails the build rather than someone's
radio.
The network backend treated "control link alive but no CI-V reply" as the rig
being in standby, and tolerated it WITHOUT BOUND. When another program takes the
CI-V session — WSJT-X through OmniRig, or the Remote Utility — the rig goes on
answering pings on the control stream while sending us nothing at all. Alive()
stayed true, so ReadState returned the cached frequency with err == nil, the
Manager never saw a failure, never reconnected, and re-published a frozen number
with a fresh timestamp on every poll. Only restarting OpsLog cleared it.
Bounded now, on the last SUCCESSFUL read. Past the grace the error is reported so
the Manager tears the session down and reconnects, which re-takes the CI-V
stream. Also fatal immediately: the CI-V reader goroutine having exited — no read
can ever succeed after that, however healthy the control link looks.
The grace backs off to minutes when the silence persists, because the two cases
pull opposite ways: a stolen session recovers on the first attempt, while a rig
switched OFF is silent for hours and re-tearing its session every 30 s would
blink the panel — and its ON button — away continuously. A good read resets it.
The decision table is pinned by a test; the standby case (never answered since
connect) keeps the old tolerate-for-ever behaviour.
ULS was wired into AddQSO alone, so an operator who downloaded it and has no
QRZ.com/HamQTH account saw nothing while typing a US call: cty.dat gives the
country, the zones, and a 4-character grid that is the ENTITY centroid — a
thousand kilometres from the station. The county and the real square were stamped
after logging, too late to point an antenna with.
The enrichment runs last in the lookup wrapper and only fills blanks, so a
provider always wins. ULS carries no name and no address, so it completes a QRZ
record and can never replace one.
The grid needed a rule of its own. refineGrid keeps what is there unless the new
value extends it — correct for a QRZ square, wrong against an entity centroid,
which is simply a different square. A per-callsign FCC square therefore beats any
4-character grid, while a 6-character one already present is left untouched.
Lat/lon are recomputed only when we actually moved the grid.
Portable calls are skipped: W1AW/4 is not what the FCC licensed.
The profile's MY_* metadata is derived from the callsign through cty.dat, and the
effect that derives it ran on every load — so opening the settings counted as
"the source changed" and overwrote whatever the operator had typed. Reported by
an operator in CQ 4 / ITU 4 handed 5 and 9: he corrected them, and each restart
put 5 and 9 back.
cty.dat gives the zones of the ENTITY, and a large country spans several, so the
automatic value cannot be treated as authoritative — it is a starting point. A
load now fills only fields that are EMPTY; a recompute that overwrites happens
only when the callsign or grid itself changes, which is the case the derivation
exists for.
The load-vs-edit distinction is a ref holding the profile id the values were last
derived from — first sight of a profile is a load.
"Last download" and an operator-chosen date are different questions, and they
now ask QRZ different ones. The automatic run wants everything TOUCHED since it
last ran (MODSINCE) — that is what returns a 2015 QSO confirmed yesterday. A date
typed by the operator names a period of OPERATING, so it maps to BETWEEN date and
today, on the QSO date.
The client-side date filter is skipped only under MODSINCE, where it would throw
away the older-but-newly-confirmed records the query exists to fetch. Under
BETWEEN it agrees with the server and stays on as a backstop.
The date window was sent as OPTION=AFTER:<date>. That was a guess, and QRZ
rejects the request outright — RESULT=FAIL with no reason — so the confirmation
download failed completely for everyone, whatever the account.
The documented option is MODSINCE, and it is the better window anyway: it selects
records MODIFIED since the date, so a QSO from years ago that was confirmed
yesterday comes back. A QSO-date window structurally cannot return those, and
confirmations are the whole point of this download — which is why the client-side
date filter is now skipped when the server did the windowing, instead of throwing
those same records away on arrival.
A refusal now falls back to ALL rather than leaving the operator with nothing.
Reported as a regression — reopens on the wrong screen — but the window code is
untouched since it was verified working: the only change to main.go since is the
background colour. So the fault is in the DATA, and there was no way to see it.
Both ends now log their coordinates, plus where the window actually landed after
the un-maximise / move / re-maximise dance. That separates the cases, which need
opposite fixes: nothing was captured, something wrong was captured, or the right
corner was captured and Windows moved the window anyway.
Reverts 30d8827. Ctrl+C / Ctrl+V already work in the app, so the WebView's
default menu only added Refresh / Save as on the neutral areas — noise in an
application window, for nothing gained. Changelog entry dropped with it.
Wails disables the WebView context menu in production, so an operator could not
paste a cluster address, an API key or a callsign anywhere in the app. Ctrl+V
did work — nothing intercepts it — but the menu is where people look, and a key
copied off a web page is exactly what you paste rather than retype.
EnableDefaultContextMenu turns it back on.
Every port box was parseInt(e.target.value) || <default>. Delete the contents
and parseInt gives NaN, so the default is written straight back: the digits
reappear under the cursor and the only way to enter a different port is to
overwrite it character by character. Reported on the cluster editor; the same
line existed in eight other places.
One PortInput component now holds the raw TEXT as its state and only tells the
parent about a value that is actually a port. An empty box stays empty while you
type; on blur an invalid one falls back to the default, so nothing is ever saved
as 0 or NaN. It adopts a value arriving from the backend only while the operator
has not started typing — re-syncing mid-edit is the behaviour being fixed.
This is the controlled-input trap the project notes already warn about: keep the
raw text in local state and derive the stored value from it.
Same slip as before the 0.21.6 release: I appended to a block that had already
shipped. 0.21.7 is back to its 12 published entries; the microwave-band fix
opens 0.21.8.
Reported on 3 cm. cat.BandFromHz stopped at 23 cm, so a 10 GHz frequency came
back EMPTY — and an empty band is not cosmetic: the QSO is logged without one,
counts in no award slot, and exports with no BAND field. The low end was short
too (2190m / 630m / 560m).
Four band tables had to be extended because four exist: the CAT one, the award
plan in app.go, the cluster spot classifier, and the frontend's. Plus the places
that LIST bands — the QSO editor and award-definition pickers (you could not set
3 cm by hand either), the statistics axis, and the award band ORDER, where a
missing band sorts to the end instead of in frequency order.
Ranges and names are ADIF 3.1.7, which is what an export has to carry.
A test now pins one frequency per band across the Go tables and asserts they
agree — that is what was missing, four hand-maintained copies with nothing
checking them. It also pins that an out-of-band frequency stays empty rather
than snapping to the nearest band, which would file a QSO under a band the
operator never used.
Left out as "internal", but the log is something operators read and send —
and the Flex meter removal, which is the same nature, was listed. Consistent
now.
An FTDX10 operator reports that changing band from OpsLog moves the rig but the
displayed frequency stays on the old band until they nudge the VFO. The existing
readback is taken immediately after the write, so it always shows the old value
and proves nothing: OmniRig queues the CAT command and sends it over serial.
A second readback is now logged ~1.5 s later, from ReadState (the goroutine that
owns the COM apartment), together with what OpsLog concluded. That separates the
two candidates, which look identical to the operator: the rig ignored the write,
or the rig moved and its rig file never re-reads the frequency.
The backend already parsed the atu object and exposed ATUStart / ATUBypass /
SetATUMemories through the Flex controller and the App bindings — only the UI
was missing, so the radio's own tuner was the one thing on the panel you still
had to reach SmartSDR for.
Placed under TUNE, which is the order of operations: the tuner needs a carrier
to measure against.
The status is decoded into words rather than shown raw. That is the point of the
block: TUNE_FAIL and "never tuned" leave the radio looking identical on its own
front panel, and the operator transmits into a bad match either way. Failed is
red, tuning amber, tuned green.
Switching station is the frequent act and editing a profile the rare one, but
the callsign opened the settings — so changing station took four clicks and a
scroll. It is now a dropdown of every profile: pick one and it activates. The
active one is ticked and disabled, and "Manage profiles…" stays at the bottom
for the rare case.
The list reloads on every profile change, so a profile added or renamed in the
settings appears without a restart.
The UTC clock leaves the header for the status bar, next to the database: in the
header it sat beside the frequency in the same weight and competed with it for
the eye, while being something you consult rather than watch.
0.21.6 was published before these landed, so its notes must stay exactly as they
shipped — a released block is a record of what an operator actually got, not a
place to keep appending. Restored it to the 11 entries in the release commit and
opened 0.21.7 for the eight that followed.
The bulk-edit line was the one subtlety: it was published in 0.21.6 and then
REWRITTEN in place to cover the filter builder. 0.21.6 keeps its published
wording; the filter half is new and gets its own 0.21.7 entry.
An operator reported migrations being very slow and sent a log with three
interleaved runs — and no way to tell one database migrated three times from
three databases migrated once. Each line now carries its target: the SQLite file
name, mysql:<database>, or baseline:memory for the in-memory pass that derives
the schema for a FRESH MySQL database (that one is fast and is not a real
database — in the report it sat between two slow runs and looked like a third).
A pass also announces how many migrations it will apply, so a run that applies
nothing is visibly distinct from one that does.
Three faults compounding, all visible in one operator's report (117k QSOs):
1. We asked for OPTION=ALL every time, so QRZ serialised the entire logbook —
56 MB — and cut it short. The parser stopped at record 27832 with "unexpected
EOF" and everything past that was never read. The window is now sent to the
server (OPTION=AFTER:date); the client-side date filter stays as a backstop.
2. The last-download date was stored RIGHT AFTER the fetch, before knowing
whether the records had been processed. So the truncated run still advanced
the window past data it had never read — and every later run skipped it. It
is now written at the end, and only when the ADIF parsed cleanly. A window
that moves past unseen data is worse than one that re-reads.
3. Which is why the run in the report ended "Confirmed 0, added 0 (of 0
returned)" despite parsing 27832 records: an earlier truncated run had
already pushed the window to yesterday, so every record was filtered out
client-side. The operator could not recover without clearing the key by hand.
A truncated download now says so in plain words, and says the window was not
moved.
My mistake yesterday: the new confirmation columns went into uploadStatusCols —
the QSL Manager's FILTER whitelist — instead of bulkEditableCols. The dialog
listed QRZ.com received status and the ten dates, and the repository refused
them at Apply, after the operator had selected 54 QSOs.
Moved to the right map. And two fields have been broken this way since long
before: State and County were offered under "Contacted station" (whose IOTA /
POTA / SOTA / SIG siblings are all allowed) but were missing from the whitelist,
so choosing one always failed. Added — they are exactly what an import loses and
what a whole run shares.
The real fix is the test. Two lists in two languages had to agree by hand and
nothing checked it, so the failure only ever surfaced as an error message at the
last click. The new tests read the ACTUAL field ids out of BulkEditModal.tsx and
FilterBuilder.tsx and assert the repository accepts every one — a field added to
the UI alone now fails the build instead of the operator.
They arrive many times a second and were dumped every 5 s, drowning the rest of
the log. They only ever existed to confirm the meter NAMES during development,
which the subscription line already does — and that one is now a single summary
instead of one line per meter, a Flex announcing dozens of them at each connect.
Grid on the UDP path — WSJT-X and MSHV can only send a FOUR-character grid,
that is all the FT8 protocol carries. The enrichment rule there is "fill only
what is empty", so the coarse JN05 always won and QRZ's JN05JG was thrown away:
roughly 100 km of accuracy discarded on every digital QSO. The lookup grid is
now taken when it EXTENDS the received square. A lookup that disagrees outright
(JN18 against JN05) is not a refinement — the station may be portable and what
came over the air is then the better record. Both rules are pinned by tests.
Manual fetch in the QSO editor — it read the CACHE, valid for 30 days. An
operator who upgraded their QRZ subscription went on getting the thin
free-account record and clearing the cached row by hand was the only way out.
The button now forces a lookup that bypasses the cache, reaches the provider and
REFRESHES the stored row, with a 15 s budget instead of 2 s: a deliberate click
must reach the network, where giving up early would fall back to cty.dat and
look like nothing happened. The automatic type-ahead lookup keeps the cache,
which is where it earns its keep.
Same fetch: it used `??`, which only guards against null. Go marshals an unset
string as "", so a QRZ record with no grid BLANKED the grid already in the QSO.
The lookup still wins — that is the point of asking for it — but an empty
result no longer erases a good value.
"Upload" was wrong for half of them: a paper QSL is not uploaded. Every entry
now says whether it sets a STATUS or a DATE, and in which direction — "QRZ.com
sent status", "LoTW received date" — which is also how the ADIF fields read.
Added: the QRZ.com received status (the column existed, it was simply never
offered) and the ten confirmation DATES — QSL / LoTW / eQSL / QRZ.com in both
directions, Club Log and HRDLog outbound only, those two having no return
channel. Dates use the same picker as the QSL Info tab, with a Today (UTC)
button; clearing the field writes an empty value, which is how a wrong date is
removed from a batch.
Fields are grouped by CHANNEL now, each status followed by its date, in the same
order as the QSL Info tab — a longer list, but nothing to hunt for.
The repository whitelist is extended to match: without it the new columns would
have been refused at write time. The old ids (qrz_upload, clublog_upload,
hrdlog_upload) still resolve, in case anything still holds one.
Statistics — the activity chart ignored the period selector: picking a year up
top left it showing the last 7 days, two controls contradicting each other. The
buttons were four fixed rolling windows anchored on the newest QSO, not
granularities. They now choose the BUCKET SIZE over the selected period, with an
Auto default and a step-up when a bucket would be too fine (the backend drops a
series past 750 buckets rather than ship 6000 unreadable bars). The hour-of-day
histogram covered a single day, too little to read anything from; it moves to
its own card with a weekday view, over the whole period.
Band map — the CW/data/phone sub-bands were shaded with the STATUS tokens, the
same amber that means "new band" on the pills drawn on top of them. A sub-band
is an identity, not a state: categorical hues now, validated in both themes
(violet failed on the dark steps — 1.9 ΔE from blue for a protan reader) and
added to the legend, since identity must never be colour-alone.
Frameless window — the OS title bar was a dead 32px band above a window that
already has its own. Minimise/maximise/close move into the app header, which
carries the drag region and double-click-to-maximise. The drag opt-out is by
ROLE in CSS, so a future button in that bar keeps working without anyone
remembering the rule.
Fixes:
- Saving settings froze the window while a device was slow: restarting a link
waits for its poll goroutine, which can sit 45 s inside an uninterruptible COM
Connect when another program holds the rig. The restart is now off the UI
path; a slow one is logged.
- Multi-screen: a MAXIMISED window was never repositioned, so it came back on
the primary screen every launch. The corner is now recorded even when
maximised (it names the monitor) and re-applied while still hidden.
- The Callsign field is marked out at rest — operators were typing the call into
Name, which sat beside it and looked identical.
- QSL dates get a real picker (native, for the OS calendar and locale order); a
malformed old value stays in a text box rather than vanishing behind an empty
one.
Also: a Support OpsLog entry in Help, and a WinKeyer protocol trace. The WK2
report (one element then a ten-second pause, sidetone that will not switch off)
is NOT fixed here: the WK1/WK2/WK3 command sets differ and a guessed fix would
break the operators it works for today. The trace logs every byte with the
command name and spells out the firmware family, which is what will settle it.
Moving the folder (C:\OpsLog → D:\OpsLog, or onto a stick) broke everything:
config.json and each profile's logbook path were absolute, so on the new
machine the pointer named a drive that no longer applied.
The logbook case was the dangerous one. db.Open CREATES what is missing, so if
the stale C: path happened to be creatable, the operator silently got a NEW
EMPTY logbook instead of an error — with their QSOs sitting untouched in the
folder they had just copied.
A path inside the application folder is now stored relative to it and resolved
against the current location at read time. A path OUTSIDE it (a synced folder,
a chosen drive) stays absolute and untouched — that is a deliberate choice; it
is only re-rooted when it has gone missing AND a file of the same name exists in
this install's data folder, i.e. the copied-folder case. With no such twin the
path is left alone so the failure is reported rather than papered over with an
unrelated database. Both rules are pinned by tests.
The Main-tab pane and the full Recent QSOs tab are the same component sharing
one storage key, but the pane is about half as wide — so it wants fewer and
narrower columns. Whichever was opened last rewrote the other's widths.
The pane now stores under "mainpane", which also scopes its award-column
visibility and widths. The full tab keeps the historical key, so its layout is
untouched; the pane starts from defaults once.
1. A language change rebuilt the column defs, which sets the anti-clobber
guard, but the effect that clears it listened to only two of the rebuild's
causes. Guard stuck on → every column change was silently discarded for the
rest of the session. Now keyed on the rebuilt defs themselves, so any future
cause is covered.
2. The cluster grid had no guard at all: the same rebuild wrote its defaults
over the saved layout, in the cache AND the database. Unrecoverable.
3. Worked-before and cluster read their state before the active profile was
known, so they looked up the unscoped cache key (always a miss) and then
saved under the scoped one. They now wait for the scope and remount on a
profile switch, like the main log.
4. GetUIPref returns an ERROR, not "", while the settings store is not yet
scoped — deliberately distinct from "unset". The frontend read it as "no
preference", rendered defaults, and the first column event overwrote the
good copy. It now retries instead of giving up.
5. The QSL manager had no storageKey, so it shared the main log's layout and
each rewrote the other.
Also: the DB write is debounced (a resize drag fired dozens of writes) with a
flush on close, and a rejected write is retried rather than dropped.
On its CAT/AUX connector an ACOM is the MASTER: it polls a transceiver and
changes band from the reply, so nothing can be pushed to it. internal/catemu
answers those polls on a second serial port, in ACOM command set 5 (Kenwood /
Elecraft): FA;, FB;, IF; and ID;, and nothing else — a wrong-length reply is
worse than none, it desynchronises the amp's parser for the following poll.
Also offered for SPE. Some amps do not poll at all but read the radio↔PC CAT
line in parallel; those never hear a responder, so an optional unprompted send
(500/1000 ms) covers them.
The TX frequency is what is sent: in split the amp must be tuned where we
transmit. Frame lengths are pinned by tests — the failure they guard against is
silent and only shows up as an amp that mistunes.
Untested on hardware.
The release prompt was answered with a missing dot and the script propagated
it verbatim into both constants, so the shipped exe reported "021.4".
That is not cosmetic: versionLess splits on dots, so "021.4" parses as [21,4]
and compares GREATER than "0.21.5" — a client on that build would be told it
is up to date forever and never offered another update. It also broke the
What's new dialog on a fresh install, where the changelog entry ("0.21.4") is
matched against appVersion by string equality.
Same code as the release otherwise; only the version string changes.
OmniRig reports the VFO pair (AA/AB/BA/BB) on the whole Yaesu range and never
the single-letter form. Only the latter was honoured, so every rig in that
family stayed pinned to VFO A: pressing SUB moved the radio but not OpsLog,
and a QSO worked on SUB was logged on the main VFO's frequency. The first
letter of the pair is the VFO being listened on — Log4OM reads it and gets the
right frequency on the same rigs, which is what showed the data was there.
The enum now wins over the Yaesu Freq==FreqB inference, which is only a
fallback for a rig file that names no VFO at all (the stock FTDX10 one answers
neither VS; nor FR; usably — verified on the air).
Split: the ON flag is still latched to survive a rig file that flips it on its
own, but the latch is now ARMED only after 8 flips in 30 s. A first cut at
3-in-15s was armed by the operator toggling split while testing, imposing the
6 s clearing delay on a radio that did not need it; a misreading file flips a
dozen times in that window untouched, so the two cases separate cleanly.
Distance (km) column added to Recent QSOs and Worked before (shared catalog).
Computed from the QSO's OWN my_grid/my_lat/lon first, falling back to the
current profile's locator: a log spans years and portable outings, so the
station a QSO was made from is not necessarily today's.
Locator: a precise QRZ/HamQTH grid is no longer overwritten by the cty.dat
entity centroid. The lookup runs several times per QSO and the provider gets
2 s; a slow second answer fell back to cty.dat and downgraded JN05JG to JN16
while name and QTH survived (they are only written when non-empty).
The OmniRig diagnostic line now logs what OpsLog concluded, not just what
OmniRig reported. icomnet.go: gofmt alignment only.
- SCP/N+1: new internal/scp downloads the community MASTER.SCP master list and a
docked two-column widget shows, as you type a call, the known calls containing it
(Partial) and the calls one edit away (N+1) — click to fix a busted call. Opt-in
in Settings → General; top-bar toggle; queried debounced on callsign input.
- Flex: OpsLog's GUI-client detection was too loose and could bind to "SmartSDR CAT"
(or DAX) — both carry "smartsdr" in the program name — instead of the real GUI
client, making SmartSDR CAT drop and reconnect in a loop while OpsLog was open.
Now it binds only to a real SmartSDR/Maestro GUI client (e.g. a FLEX-8600M's
integrated screen) and excludes cat/dax; dropped the risky empty-program fallback.
- Telemetry: on a fresh install the callsign isn't set at launch, so the once-a-day
heartbeat recorded the machine UUID. Now it waits (~10 min) for the operator to
enter their callsign before sending, falling back to the UUID only if none appears.
For an entity resolved only via cty.dat (e.g. a French call not on QRZ/HamQTH),
the provider block sets a coarse country-centroid grid. The worked-before backfill
now overrides that with the precise locator from the last QSO with this call, and
takes that QSO's lat/lon (derived from the grid when the record stored none) so
the map and saved record stay consistent. A real provider grid still wins.
Moved the (unreleased) worked-before backfill entry into a new 0.21.2 changelog
block, since 0.21.1 is already out.
When a callsign resolves only to cty.dat (not on QRZ/HamQTH, or no lookup service
configured) — or the lookup errors — enrich the entry from the most recent QSO
already in the log with that call. Fills ONLY the fields the provider left empty
and the operator hasn't edited (name, QTH, grid, country, address, state, county,
lat/lon, zones, continent, email, QSL-via), so a real QRZ/HamQTH hit is never
overridden. Uses the worked-before entries (qso_date DESC, [0] = latest) via a
live ref so it works regardless of the lookup/worked-before debounce ordering.
rouggy