Renames the Hardware section to Amplifier and adds an amplifier-type selector
(4O3A PowerGenius XL, SPE Expert 1.3K-FA / 1.5K-FA / 2K-FA) plus a transport
choice for the SPE amps: USB (serial COM + baud) or Network (RS232-to-Ethernet
IP:port). PGXLSettings gains Type/Transport/ComPort/Baud (keys keep the pgxl.*
prefix for back-compat). PowerGenius still drives over TCP; SPE settings are
stored but control is not wired yet (needs the SPE serial protocol).
- Denkovi (FT245 D2XX) now selectable as 4 or 8 relays (a 4-relay board just uses
the low nibble); NewDenkovi takes a count, driven by the device's Channels.
- New 'usbrelay' backend: cheap CH340/LCUS USB-serial boards over a COM port
using the common A0 protocol ([0xA0][relay][state][checksum]); write-only, so
Status is a shadow. Channel count configurable (1/2/4/8/16).
- StationDevice gains Channels; deviceRelayCount() drives label/relay counts for
the variable-size types. Device editor: channel selector + COM-port picker
(usbrelay) / FTDI-serial (denkovi).
Both untested on hardware; the A0 command set / Denkovi bit order may need a tweak
after a live test.
Award refs are now computed once and stored on the QSO as a JSON column
(award_refs, e.g. {"DDFM":"74","WAJA":"12"}) instead of recomputing the whole
award engine on every grid page load. Written on log/edit/UDP-import and
bulk-recomputed when an award definition or reference list changes; a one-time
per-logbook backfill materializes pre-existing QSOs. The grid reads the column
directly like any other field, so it's fast and available everywhere (including
the shared MySQL logbook).
Also fix per-profile grid column layout: the DB copy was already per-profile,
but the localStorage cache used one global namespace and shadowed it, so a
profile switch kept the previous profile's columns/widths. gridPrefs now scopes
the cache by active profile id and the grids remount on profile:changed.
GetQSORate now returns both the active operator's rate (their own performance)
and the whole station's rate (all operators combined). RecentRateBreakdown
computes both in one scan of the recent rows (per-operator + all-operators),
replacing RecentRate.
ON AIR badge (bottom status bar, shown when live-status publishing is on): a
blinking red light + "On air" when a QSO was logged in the last 5 min, dim
"Offline" otherwise. Seeded at launch from LiveLastQSOAgeSec so it's right
immediately, flips online on qso:logged, expires via a 10s tick.
Auto-updater UI: the update check now also runs every 10 minutes, and the
update notification downloads and installs in-app — a live progress bar
(update:progress) then OpsLog restarts on the new build. Falls back to opening
the release page when there's no auto-download asset or on error (retry).
Regenerated bindings for DownloadAndApplyUpdate / LiveLastQSOAgeSec.
Automatically switches the Station Control relay boards from the rig's
current frequency / band. Each relay carries one rule: off (manual), a
frequency window (ON inside [lo,hi] kHz, OFF outside), or a set of bands
(ON on those bands, OFF elsewhere). Evaluated on every CAT frequency/band
change; a relay is only switched when its desired state actually changed,
so tuning within a range doesn't hammer the board.
A cached atomic flag keeps the CAT hot path a no-op when the feature is off
(important during FT8 slice churn). Saving re-applies from the live
frequency so a changed rule takes effect immediately.
New Settings → Hardware → Relay auto-control section: master enable plus a
per-relay mode (Off / Frequency / Band) with kHz range inputs or band
chips, per configured relay board. i18n EN + FR. Azimuth/Time modes (the
other two PstRotator tabs) are left for later.
Watches a configurable list of external ADIF files (fldigi RTTY logbook,
N1MM, VarAC…) and imports newly appended QSOs automatically. Each record
goes through the existing UDP-log path, so it gets full enrichment, ±2-minute
dedup (shared udpLogMu, can't race the UDP auto-log) and automatic upload to
the configured external services — no per-file toggles like Log4OM.
A newly added file starts at its current size (offset -1 sentinel → size on
first scan), so the QSOs already in it are NOT bulk-imported; only contacts
logged after it was added come in. Reads only up to the last complete <eor>
so a half-written record waits. Handles truncation/rotation (re-reads from 0,
dedup protects) and persists per-file offsets without clobbering a concurrent
UI edit of the file list.
New Settings → ADIF monitor section: master enable + add/remove/toggle files.
Backend emits adifmon:imported → the grid refreshes and a toast reports the
count. i18n EN + FR.
rouggy