rouggy
released this
2026-07-29 19:55:17 +07:00
| 15 commits to main since this release
Changelog
- chore: release v0.22.0
- fix: WinKeyer 2 sent the dit/dah ratio to the key-compensation command
- docs: changelog block becomes 0.22.0, and the duplicated CW entry is merged
- docs: name the rig setting that makes the voice keyer inaudible
- feat: a level control for the voice keyer, and name every CAT backend in its PTT list
- fix: the PWR bar stayed at full scale after transmitting
- fix: the Yaesu power meter is not linear — calibrate it on three points
- fix: hold the TX meters through the gaps between words
- fix: power is RM5, not RM4 — the CW keying was the experiment
- chore: log the power setting with the Yaesu meters, to identify the wattmeter
- fix: read the real SWR on the Yaesu, and show the ratio
- fix: the Yaesu SWR bar showed a meter unrelated to the antenna
- chore: sample the Yaesu meters throughout a transmission, not at its start
- fix: CW speed drove the wrong keyer; survey the meters to find the SWR one
- docs: FTDX10 confirmed — no CAT keying, the serial DTR keyer is the way
- docs: name PC KEYING = DAKY, the setting that should enable CAT keying
- docs: an FTDX10 has no CAT keying command — say what works instead
- fix: read the rig's answer to KY — it was killing the CAT link, silently
- fix: the FTDX10 refuses KY; — stop waiting on a status it will never send
- fix: a CW macro knocked the Yaesu CAT link over
- fix: the Yaesu keyer refused to send — a status reply we read too strictly
- fix: the Yaesu keyer reported "Rig CAT offline" while CAT was working
- fix: the Yaesu keyer selection was thrown away when read back
- fix: the Yaesu keyer asked for a COM port it does not use
- fix: Antenna Genius drew both ports on the same antenna
- feat: CW through the Yaesu keyer — fifth CW engine
- fix: the Yaesu panel showed the TRANSMIT frequency as the main VFO under split
- feat: the Yaesu console follows the mode — CW gets its own controls
- feat: colour the Yaesu S-meter like a real one — green, amber past S9, red at +20
- fix: SPLIT placed the transmitter on a stale VFO; share the meter widget
- feat: Yaesu panel — sideband on re-click, split readout, one-touch up 1/up 5
- fix: centre the Yaesu panel like the Icom and Flex ones
- fix: Yaesu panel — S units, sidebands, three-step ATT, readable sliders, own tab
- feat: Yaesu control panel (meters, bands, DSP, TX), and drop a stale Flex hint
- feat: native Xiegu CAT backend (G90 / X6100 / X6200 / X5105)
- fix: accept Hamlib's VFO-prefixed commands — JTDX could not set the frequency
- feat: share the CAT link with other programs (Hamlib NET rigctl server)
- feat: native Yaesu CAT backend (FTDX10 / FTDX101), no OmniRig
- fix: band change from OpsLog left the frequency on the old band
- feat: bulk-edit the contacted station's gridsquare
- test: prove the status filter filters; fix a regex escape in the filter builder
- feat: IC-7300MKII, and two Icom addresses that were plain wrong
- fix: Icom over LAN froze on the last frequency after WSJT-X released the rig
- feat: the offline FCC database answers during entry, not only at save
- fix: hand-corrected CQ/ITU zones came back wrong at every restart
Downloads