rouggy
01d0b8f22b
The log settles it, and it was not mute. Mute works: '→ mute:0,true;' and the radio answers 'mute:0,true'. What happens is that the squelch REFUSES to go off — we send 'sql_enable:0,false;', the radio echoes false, and eighty milliseconds later announces 'sql_enable:0,true' again. Six times in the log, always the same shape. The SQL lamp coming back on right after a MUTE click is that revert landing, not the mute doing it. So the optimistic hold is fixed rather than the phantom. It was a fixed 1.2 s, which is wrong in both directions: too short for a setting the radio never echoes at all (AGC), and too long for one it refuses, where it showed the operator a lie for a second. The requested value now stands while the radio says nothing about that setting, and the instant the radio reports any change for it, its word replaces ours. A refusal is therefore visible immediately, and an unechoed setting still sticks. Also from the same session: filters per MODE — the narrow end in CW, the voice widths in SSB, a middle set for the digital modes — because 250 Hz in SSB and 2.8 kHz in CW are buttons nobody presses. And APF is shown only in CW: it rings a single tone out of the noise, which is a CW tool and nothing else.
Transceiver Control Interface
Introduction
TCI (Transceiver Control Interface) is a network interface for control, data transfer and synchronization between transceiver/receiver, contest loggers, digital mode software, skimmers and other software, as well as external power amplifiers, bandpass filter units, antenna switches, radio controllers and other devices.
TCI was created as a modern alternative to the outdated COM port and audio cable interfaces, it uses a full duplex web socket protocol that runs on top of a TCP connection and serves for server-client communications, providing cross-platform connectivity. Transceiver works as a server, all other software and devices as clients. The server and clients can be inside the same computer (program-server, hardware log, etc.-clients) and/or in separate physical devices connected through the local network (classical transceiver, power amplifier, antenna switch, FFT unit, etc.).
The TCI interface contains basic transceiver control commands (analog of CAT system), receives CW macros from clients and broadcasts them, outputs transceiver IQ stream to clients, receives spots from skimmers and Internet clusters, receives/outputs audio signal to work in digital modes.
The TCI uses an extensible architecture and can be supplemented with new functions and commands, while keeping the old ones operational. Thus, the TCI interface can be extended and supplemented to meet the specific needs of any software manufacturer and/or device manufacturer (receivers, transceivers, power amplifiers, switches, etc.). The presence of a device identifier allows the manufacturers of transceivers and receivers to switch to the TCI interface while maintaining the device model designation. The extensibility of the TCI interface allows you to create an individual set of commands and functions for each device model, while maintaining the basic command set inherent to all transceivers.
Our company advocates universal unification of data exchange between devices and software by creating the TCI interface for this purpose. Modern transceivers and software must communicate using one protocol - the TCI protocol.
Interface description
Any command represents an ASCII string that contains a command name and a list of arguments corresponding to this command. There are reserved characters that cannot be included in the command name and command arguments.
List of reserved characters: «:», «,», «;».
Command structure:
- Name of the command;
- Separating character between command name and arguments «:»;
- Separating character between arguments «,»;
- End of the command character «;».
If a command has no arguments, an end of command symbol is placed after the command name. If the command is invalid, it is ignored. The case of letters does not matter.
The ExpertSDR3 program acts as a server, which can have several client connections at the same time, they will be synchronized with each other by the server. When connecting to the ExpertSDR3, the client receives the current status of the ExpertSDR3, first sending initialization commands, then parameters to set the status, such as frequency, modulation, etc.
When a parameter change occurs in the ExpertSDR3 (server) program, the server notifies all connected clients, i.e., clients do not need to poll the server constantly, any change of state will be sent in time to all clients. If the client sends a new state, the server will set it to itself, as well as send it to all clients, that is, the server acts as a synchronizer. All clients connected to the server will be automatically synchronized. This way of work allows to minimize network load, reducing traffic.
The TCI protocol implements the transmission of receiver IQ stream to clients, which is necessary for the work of special skimmer software, they automatically find the station and decode it throughout the band, and it also allows you to record radio signals in the file.
TCI is also used to transmit audio signals of the receiver to clients and to receive audio signals from clients, i.e., the client can transmit audio signals to ExpertSDR3 for radio transmission. The audio stream exchange is designed to work with digital modes, where encoding and decoding is performed by third-party software, as well as in voice modes, where audio macros can be broadcasted, which is very much in demand in contest loggers.
When working in contests, it is important to record all on the air operation, for this purpose the audio stream from the line-output is sent to all clients. The resulting audio stream can be recorded to a file or played back with a PC sound card.