TCI already carries the frequency, the mode, the meters and now the audio.
It also carries everything else about the radio — and OpsLog was logging
most of it once as '(unhandled once)' and throwing it away. The console is
mostly a place to put what was already arriving.
That makes it the cheapest panel here, and it is worth saying why. A K3
console costs a command and a reply for every value it shows, which is why
it reads its settings in a rotation and its meters only while on screen.
TCI PUSHES: the radio announces its drive, its filters, its noise blanker
and the rest on connect, and again whenever any of them changes —
including when the operator changes them in ExpertSDR3's own window, which
this panel therefore follows without asking anything.
What it drives: drive and tune drive, mic gain, TUNE, volume, mute,
squelch and its threshold, NB, NR, ANF, APF, AGC speed, the passband, RIT
and XIT with their offsets, and the VFO lock. The S-meter is a real dBm
reading, so its S units are arithmetic rather than the calibration guess a
K3's meter needs.
Setters never update the cached state. The radio answers with the new
value, and taking its word is what keeps the panel honest when a setting
is refused, clamped, or changed at the radio a second later — the one
exception being a slider mid-drag, held for 900 ms so it is not dragged
back by its own echo.
Capped width and centred, like the other consoles. Also offered as a
docked pane — and the Elecraft console is offered there too now: App has
always had that pane, Settings simply never listed it.
The specification settles what a night of experiments could only guess at.
TRX takes an optional THIRD argument naming the signal source — tci, mic1,
mic2, micPC, ecoder2 — and TCI 2.0 says it plainly: 'The signal for
transmitting is always taken from the microphone selected in the
ExpertSDR3. If a third-party software connected via TCI wants to transmit
its audio signal, you must specify the third argument - TCI.'
Without it the radio sends no chrono at all, whatever the mode. That is
what the SSB attempts ran into, and what was misread here as 'digital
modes only' — the mode was never the rule, the missing argument was.
So OpsLog says it, following the 'To radio' device: 'tci' when the voice
keyer owns the transmission, nothing at all otherwise, which leaves the
operator's own microphone alone for every other PTT. Nobody has to find
that setting in ExpertSDR3 and set it again for every mode, which is how
it is remembered there.
Two more things from the same document. A chrono with no audio ready is
now answered with silence rather than left unanswered — the vendor calls
that preferable. And the receive stream declares float32 and two channels
instead of trusting the defaults: they are the documented defaults, but a
default is something another program sharing this radio can have changed,
and a stream in an unexpected format is heard as noise rather than as a
mistake.
The TCI section of the audio settings was an investigation: open the
stream, read what arrives, record ten seconds to listen to, key a tone.
It answered every question it was built for — the frame layout, the
sample width, that the radio asks rather than follows a clock, that the
transmit audio source decides — and confirmed 80 W on real hardware.
None of that belongs in front of an operator now. The radio is simply one
of the devices in the two dropdowns, and choosing it IS the configuration:
one control, in the place where the question is already being asked.
Keeping the tick box beside it would have been two switches for one
decision, with the second one where nobody looks.
Gone with it: the stream/record/probe bindings, the audio.tci_rx setting,
and twenty-four translation keys. The plumbing they proved out stays and
now carries the voice keyer.
A SunSDR carries its audio on the same WebSocket as its commands, so
OpsLog can take it directly: no virtual cable, no second sound card, no
Windows mixer between the recording and the air. The radio appears as a
device in both audio lists and can be chosen for either direction.
Everything here was settled on real hardware over one evening, and none of
it was guessable from the documentation:
- The receive stream answers format=3 for four-byte floats, so the
sample width is derived from the frame rather than trusted from the
field.
- The radio asks for transmit audio only when the transmission is the
CLIENT'S, and only when its transmit audio source is TCI rather than
the microphone.
- The chrono is a REQUEST, not a clock: no payload, carrying the size it
wants, 47 times a second. Audio goes out in answer to it and never on
a timer of our own — a timer was the first attempt and all 234 frames
of it were ignored.
Confirmed: a clean test recording, and 80 W out of a 1 kHz tone.
The radio now appears as a device in both audio lists — 'Radio (TCI
network audio)' — so the receive audio and the voice keyer can both take
the CAT link instead of a sound card. No virtual cable, no second card, no
Windows mixer between the recording and the air.
The transmit side reuses the exchange the tone probe established, with a
WAV in place of the sine: the radio asks, we answer with the next slice,
and it sets the pace. The message is converted once, up front, rather than
per frame — a voice message is a few hundred kilobytes, and resampling
inside a callback that has 21 ms to answer would put arithmetic on the
path where a late frame is a gap on the air.
The PTT is untouched by all this: the keyer keys before and unkeys after
exactly as it does with a sound card, so a transmission is bracketed by
the same code whichever way the audio travels. And the playback runs OFF
the CAT goroutine, since everything else about the rig goes through that
one place and a ten-second message would otherwise freeze the frequency
display and the antenna following for ten seconds.
Two refusals rather than silent failure. A radio that has gone away stops
being offered as a device at all, and a radio whose transmit audio source
is still the microphone is caught within a fifth of a second — a voice
keyer that transmits silence is worse than one that says why it will not.
Elecraft's release note settles it: SW; returns the most recent reading in
transmit or TUNE as three digits in tenths of a ratio — SW023 is 2.3:1,
and SW999 is the 99.9:1 it reports instead of infinity.
This asked for four, so every answer failed to parse and the bar stayed
empty for the whole transmission. A tester saw exactly that: no SWR at
all, which reads as an unsupported radio rather than an off-by-one.
SW also comes out of the probe list. It is known now, and asking again
mid-transmission costs a round trip on the link the carrier depends on.
Transmit over TCI is confirmed on a SunSDR: 80 W out of a 1 kHz tone at
70% of full scale into 80% drive, every request answered.
Which makes the earlier rule wrong. 'Digital modes only' came from a real
observation — SSB silent four times over, DIGU answering at once — but the
mode was a coincidence. ExpertSDR3 has a transmit audio SOURCE, microphone
or TCI, kept per mode, and it was on the microphone in SSB. Refusing SSB
would have blocked the one thing a voice keyer exists for.
So nothing is refused on the strength of the mode. The radio declares what
it wants by asking for audio, 47 times a second when it wants any: key,
wait for one request, and stop within two tenths of a second if none
comes — naming the setting to change rather than theorising about it.
That is better on three counts. It works in SSB when the source is set
right, it cannot be wrong about a mode nobody thought to test (AM, FM,
RTTY), and a misconfiguration costs a quarter-second of carrier instead of
five seconds.
The transmit path works: six passes, the radio asked 231 times and was
answered 231 times, none missed, and the tone was there on the panadapter.
What was missing was power on the meter, and the cause was the level. The
tone went out at a quarter of full scale, out of caution, into a radio set
to 15% drive — enough to draw a clean signal and not enough to move a
needle. In a digital mode the radio expects a line level it can drive to
full output; the POWER is its own drive control, so sending quietly only
wastes the range. Now 0.7, short of 1.0 to leave room for the peaks.
The start line carries both numbers — ours and the radio's drive — because
a quiet transmission has two possible causes and one line should settle
which, rather than an evening of guessing. Reading 'drive' off the radio
is the only reason it is parsed at all.
Three transmissions on a real SunSDR settled how the transmit side works,
and none of it was guessable from the documentation.
The radio asks for audio only when the transmission is the CLIENT'S: with
the operator keying the microphone it sent 282 receive frames and nothing
else. And it asks only in a DIGITAL mode — keyed from here in SSB it stayed
silent four times over, and answered in DIGU immediately. In SSB the
modulator is wired to the microphone, which is also the honest answer to
'why can I hear myself but not the tone'.
The chrono turns out to be a REQUEST, not a clock. It carries no payload —
the message itself is the ask — and it names the size it wants in the
header: 2048 samples, two channels interleaved, 47 times a second, which
is 1024 pairs at 48 kHz, exactly real time.
So audio goes out in answer to a request and never on a timer of our own.
The timer was the first attempt and the radio ignored all 234 frames of
it. Answering also hands the pacing to the radio: no drift, no buffer to
tune, and the size taken from what it asked for rather than from what we
assumed. The sine keeps its phase across frames, since one restarted every
frame is a click 47 times a second.
A pass in SSB is now refused rather than attempted. It keys the
transmitter, produces nothing and teaches nobody anything — and it is
still a transmission.
The feed mechanism is the one the voice keyer will use: WAV samples in
place of the sine, everything else unchanged.
A first real transmission settled one question and raised a better one.
With the receive stream open and six seconds of transmit, the radio sent
282 frames of receive audio and NOTHING else: no chrono, no transmit
audio. So the chrono the documentation describes is not offered to a
client that merely happens to be connected while the operator keys the
microphone, and waiting for it to appear is waiting for nothing.
The reading that fits is that the radio asks for audio when the
transmission is the CLIENT'S and takes the microphone when it is the
operator's — which makes the experiment obvious. Key it from here, push a
1 kHz tone, and watch. Chrono frames appearing gives their size and
cadence by measurement instead of by guesswork; no chrono but a tone on
the meter is just as useful, because then the pacing is optional and the
voice keyer can push frames at the rate the stream already runs at.
A tone rather than silence so the answer shows on the power meter and not
only in the log.
It transmits, so: an explicit button inside a warning box, five seconds,
capped at ten, and every path out unkeys — including the panic that has
not happened yet and a socket that dies mid-tone. A transmitter left keyed
by a defect is the one fault here that would reach somebody else's band.
Writes are now serialised too. send() held the lock only long enough to
read the connection, which was enough while every command came from the
poll loop; a stream of audio frames from a second goroutine is not, and
gorilla panics on a concurrent write rather than failing quietly.
The first transmit test came back with a log that said nothing, which is
the one answer that cannot be read: either no transmit frames arrived, or
they arrived and went unlogged.
So each pass is now bounded by a line of its own, and every stream type is
counted without limit. A pass that reports 'receive audio: 240, and
nothing else' is a result — it says the radio sends no chrono unless
something more is asked of it — where a log with no transmit lines was
merely a silence. The forty-frame logging budget is also handed back to
the transmit types on each pass, since it was always spent on receive
audio long before anyone got round to keying.
The start line says whether the receive stream is even open, because a
radio with nothing streaming has no reason to send chrono, and that is the
likeliest reason the first attempt saw nothing.
The network option IS implemented — the same ASCII CAT over TCP instead
of a cable, for a ser2net bridge, an Ethernet-serial adapter, or a radio
exposing its raw CAT port. What was wrong is how it was offered: the COM
port and the network address sat side by side with nothing to say that
the address wins whenever it is not empty.
Worse, the example address read 192.168.1.50:4532. That is Hamlib
rigctld's port — a different protocol, and the one OpsLog SERVES under
'Share CAT'. Anyone copying the example was pointing the radio link at
OpsLog's own server.
Now one choice, then the fields that belong to it. And when the far end
answers something that is not the radio's CAT, the error says that rather
than 'check the baud rate', which over TCP is advice about a setting that
cannot be the cause.
The frame log had one budget for the whole session, and the first forty
receive-audio frames spend it in under two seconds. A transmit-chrono
frame — the thing the voice keyer will have to answer, and whose size and
cadence cannot be read off the documentation — only appears once the
operator keys the radio, by which time nothing would have been logged.
Counted per type now, so the first frames of each kind are recorded
whenever they turn up.
The SunSDR announces its own stream at connect —
audio_stream_sample_type:float32 and audio_stream_channels:2 — and both
were being logged as unhandled while the code worked the format out from
frame arithmetic. The declaration is better evidence and arrives before
the first frame; the arithmetic stays as the check on it. The channel
count now drives the mix-down instead of an assumed stereo.
Adds a ten-second test recording, written as a WAV beside the QSO
recordings. Counting frames proves a socket is delivering bytes; it says
nothing about whether those bytes are the receiver's audio, at the right
rate, in the right order. A stream decoded with the width wrong or the
samples misaligned counts exactly as well as a correct one and sounds
like a fan — so the test is a file the operator can play, the same way
the CW decoder was settled on the air rather than on a spectrogram.
The file is written at the rate the RADIO reported, not a constant: a
recording at the wrong rate plays at the wrong speed, which is the one
fault that would be blamed on the decoding.
A real SunSDR answers format=3 where this expected 0 — and 0 was read
from the documentation, which is exactly the kind of detail a memory of a
document gets wrong. The stream was refused outright: 'format=3, expected
float32', zero frames, silence.
Swapping one magic number for another would only move the guess, so the
width is now MEASURED: the header says how many samples the payload
holds, and dividing gives the bytes per sample. Four is float32, two is
16-bit PCM scaled to the same -1..1 the rest of the audio path uses, and
anything else is reported rather than mangled. That stays true whatever
number the format field carries on the next firmware.
The transmit meters were read on k.tx, which records only that OpsLog
keyed the radio. An operator using the front-panel PTT, a footswitch or
the mic button therefore had a panel that believed the rig was receiving
— and since the power and SWR bars are read only while transmitting,
they were never read at all. IF carries the radio's own transmit bit;
that is what decides now.
The meter probe logs RAW answers rather than parsed numbers, and asks a
wider set (SM, SMH, BG, SW, PO, TQ). A command answering in a shape we
did not expect is the interesting case, and parsing hid it behind the
same dash as a command the radio refused — which is what still stands
between us and a working SWR reading on a K3.
Both are the same bug. ReadState returns early while transmitting — the
rig answers '?;' to IF; then, and treating that as a fault used to drop
the link — but that early return also skipped the panel update and the
meter read.
So the panel believed the radio was still receiving. Pressing MOX again
therefore sent ANOTHER transmit command instead of RX, and the K3 stayed
keyed, exactly as reported. And the power and SWR bars were only ever
read at the one moment they mean nothing.
Reading meters while transmitting needs one more guard: a '?;' then says
when the question was asked, not what the radio supports, so the
unsupported-command memory is suspended for that read. Without it, one
badly timed refusal would silence a meter for the rest of the session.
Adds RIT/XIT offset control (±10/±100 Hz, offset shown), a 4.0 kHz filter
button for FT8, and logs the K3's icon word when it changes: there is no
command for 'is the ATU in line', the reference says the switch functions
show up as icon changes, so an operator toggling the ATU while watching
the log will name the bit and the button can then light up honestly.
A SunSDR already carries its receive audio on the same WebSocket as its
commands, so a virtual audio cable and a second sound card are two pieces
of plumbing an operator installs for no reason. This is the receive half:
what the QSO recorder and the CW decoder need.
The reader now looks at the frame type. It used to ignore it and split
every frame on ';' -- harmless only for as long as no stream was ever
opened, since audio bytes would otherwise have been handed to the command
parser a hundred times a second.
NOTHING HERE IS CONFIRMED ON A RADIO. The header layout comes from the
TCI documentation, and the stream-type numbers are exactly the sort of
detail a document gets right and a memory of it does not -- so the first
forty frames of a session are logged verbatim, and a test bench in
Preferences > Audio reports the sample rate the radio chose, the frames
arriving and the peak level of the last second. 'The stream is open' and
'audio is arriving' are different claims and only the second is worth
anything to whoever tries this first.
Transmit (the voice keyer) is the other half and is deliberately absent:
it has to answer the radio's chrono packets at the right pace, and that
is worth doing once the format is settled on real hardware.
SWT20 was written from memory of the reference rather than from Table 7,
and 20 is not an ATU switch at all — it would have pressed something else
on a real K3. An operator read the table out for us: switch 19 is the ATU
row, TAP for a tuning cycle and HOLD for tuner in line or bypassed.
Adds the HOLD as its own ATU button, because on the radio they are two
different things: tuning is a cycle you start, bypassing is a state you
leave it in.
Power takes 0-110 W on an Elecraft, per the reference — a K3 makes a
little over its rated output — while a Kenwood keeps 200.
Reported from a real FTDX101, and each one is a different kind of wrong.
MIC GAIN was read and written through the 0-255 scale the audio gains
use, but the CAT reference gives MG000-100. A rig set to 80 therefore
showed 38, and moving the slider sent 204 — outside the range the radio
accepts, so it refused the command and the slider sprang back. That
snap-back was the symptom; the scale was the cause.
POWER was capped at 100 W by the slider, not by the radio. There is no
CAT command for 'how much power can you make', so the ceiling comes from
the model name, with the rig believed if it ever reports more than the
table expects — it has just proved what it can do.
NAR is the narrow IF filter, and on a rig that does not implement NA the
button showed a state the radio never gave and did nothing when pressed,
which reads as a fault in the radio. Now shown only when the rig answers,
with a tooltip saying what it is.
Also: the frequency readout steps the Hz digits under the wheel, not just
the kHz ones. Zero-beating a CW signal is a few tens of Hz and it was the
one move the display would not make. And the split chaser is CW-only —
its marker comes from a CW skimmer.
So the tester can exercise everything in one session instead of one
control per build: RF and mic gain, squelch, preamp, attenuator, NB, NR,
AGC, filter width, antenna, RIT/XIT with a clear, and the keyer speed.
The analogue scales differ between an Elecraft and a Kenwood — RF gain
000-250, mic 000-060, squelch 000-029 against 0-255 — so each is mapped
through its own full scale and shown as a percentage. Using one rig's
range on the other silently halves or doubles every setting.
Antenna only appears when the radio answers AN: a K3 without the internal
ATU has one socket, and a switch that goes nowhere is worse than none.
The Elecraft backend already existed; what was missing was somewhere to
operate the radio from. This adds the panel, on the Kenwood-dialect
client the K3 already speaks, in a tab of its own beside the Yaesu and
Icom consoles.
Scope is the six controls asked for and nothing else. Every extra command
added without a radio to test it against is a control that may or may not
do what its label says, and a K3 exposes dozens.
No K3 was available while writing this, so the two halves are treated
differently. The setters are the commands the reference documents
unambiguously and whose effect is visible and reversible (PC, AG,
TX/RX). The meters are the opposite: their scaling differs by model and
firmware, so the raw answers are logged next to the power setting, the
panel says the scaling is provisional, and an unmeasured SWR shows as
'—' rather than as a perfect 1.0 — a good match on an antenna nobody
measured is the reading that costs a radio.
ATU tune sends SWT20 (the K3 front-panel tap) and logs exactly what it
sent, so a wrong mapping names itself instead of leaving an operator
guessing which button OpsLog pressed.
Working a DXpedition split means guessing where it listens. The useful
information is not the callsign the DX answered but the FREQUENCY that
station was calling on, and a CW skimmer already marks it: SDC posts each
decoded report to the panadapter as a spot.
Those spots reach OpsLog through the radio's spot feed. On a marker, the
TRANSMIT slice moves there plus a signed offset; the receive slice never
moves, because losing the DX is worse than missing a call. The marker
text is a setting -- it is chosen in SDC by the operator, so any constant
here would be wrong for whoever chose otherwise -- and the switch is a
button beside SPLIT, since it is turned on when a DXpedition appears and
off when it is worked.
Moves are throttled and ignore a marker landing where the slice already
is: a busy pile-up produces several reports a second and the slice would
otherwise never be anywhere long enough to call.
The spot feed is now subscribed to unconditionally. It was tied to
OpsLog's own spot overlay, so an operator running SDC with the overlay
off received nothing -- the reason no foreign spot was ever logged. The
connect-time 'spot clear' stays behind the overlay flag: it wipes every
spot on the radio, a skimmer's included.
Chasing a split pileup with a CW skimmer means acting on the report the
DX just sent: SDC posts what it decodes as panadapter spots, so the 5NN
is already on the radio and OpsLog already subscribes to 'spot all'.
What is not known is the shape of those spots -- which field carries the
report, whether it is the callsign or the comment, what source the
skimmer names itself. Guessing produces a feature that never fires, so
this logs the first 60 foreign spots of a session verbatim and does
nothing else. Bounded because a skimmer posts hundreds an hour.
HAMLOG.online is a seventh external service: one API key, one ADIF record per
QSO, immediate / delayed / on-close like the rest. They publish no API
documentation, so the protocol is read from THEIR OWN client — the HAMLOG Agent
(github.com/hamlogonline/Agent), which is the authoritative source short of
asking them:
POST https://hamlog.online/api/agent/
{"ADIFADD": {"APIKEY": k, "ADIFDATA": record}} → {"STATUS":"OK"}
{"KEYSTATUS": {"APIKEY": k}} → {"STATUS":"OK","CALLSIGN":…}
Success is STATUS == OK, not "no ERROR field": their failure carries ERROR and
no STATUS, and reading an unknown reply — a proxy page, a maintenance notice —
as an acceptance is how a contact goes missing without anyone noticing.
KEYSTATUS buys something no other service here offers: the key can be checked
BEFORE the first QSO, and the answer names the account. A key pasted from
another callsign is caught in the settings panel rather than through a week of
silent refusals.
Their confirmations are also an award source now, ticked like LoTW rather than
expressed through "custom". It reads the ADIF extras, not a column: the standard
names a field for hamlog.EU and none for hamlog.ONLINE, and borrowing the other
site's field would write a falsehood into every exported log. Three plausible
key names from their own export are accepted too, so nobody has to rename a
column by hand after an export.
Yaesu gains antenna selection (AN), remembered per band — the antenna picked on
a band comes back with it, with no table to fill in anywhere. Rigs with one
socket never answer AN and never show the row; the log says which case it is.
And a serial port that is refused now names its likely holder. OmniRig stays
resident once activated and keeps the port of the rig configured in it, so a
native backend never gets it — "Serial port busy" alone accused nobody, and an
FTDX10 spent a morning being blamed for it.
An Icom reached over the LAN streams its receive audio through the Icom
protocol, and Windows sees no sound card for it at all — the audio settings
could only offer the PC's own microphone, so "From radio" had nothing right to
point at and the QSO recorder had nothing to record. The recorder now accepts a
PUSHED source: the decoded stream goes to the speakers and to the recorder
alike, with no virtual cable to set up. Which source it uses follows the CAT
backend, and it is restarted only when that answer changes, so an ordinary
settings save never cuts a recording in half.
OmniRig no longer sends SetSimplexMode to a Yaesu when tuning. It is a silent
no-op on some — an FT-891 logged OK on every spot click while FreqA never
moved — and actively harmful on others. From an FT-2000 log, one QSY:
Vfo="AB"(0x80) Split=0x10000 (off) the operator's state
Vfo="BA"(0x100) Split=0x8000 (ON) after SetSimplexMode
The rig-agnostic "receive and transmit HERE, simplex" call turned split on and
moved reception to VFO B. OpsLog then displayed B — reading the radio correctly,
after having moved it itself. Icom is untouched: there the call is the
authoritative one and the direct write is unreliable.
Also:
- the NEW county badge shows in the entry form itself, inside the field,
where the operator is deciding whether to call.
- the basemap buttons clear the zoom controls; Light sat a few pixels from
the minus button and was being clicked by mistake.
- French cluster status: DÉJÀ CTC reads DÉJÀ QSO.
Panadapter spots are now worth reading. The comment carries the spotter, the
entity and the status in DXHunter's own shape — "CQ up 2 [F4BPO] [Franz Josef
Land] [New Slot]" — which needed two things nothing documents: SmartSDR splits
its command line on SPACES, so the words ran together until every space became
non-breaking; and it truncates past ~60 characters, so the cluster's own words
are trimmed first and the three brackets always survive. RBN column padding is
collapsed on the way in, or a preserved run of spaces opened a gap wide enough
to push the rest off screen.
"Already worked" means the CALLSIGN is in the log, not the entity: saying it of
a station never contacted was simply wrong. Each status can also be kept off the
panadapter entirely, and the WSJT-X decode spots obey the same switches — the
palette governs the panadapter, not one of the two things that feed it.
And the radio is no longer hammered: a spot whose frequency, colour and comment
are unchanged is not removed and redrawn. A busy skimmer feed re-spots the same
station every few seconds; one two-minute session sent 2128 adds, 88 of them for
a single callsign, and the display did not move a pixel for any of them.
CI-V, from an IC-7850 that kept killing JTDX: a reply the rig sent to another
controller on the same bus is no longer taken for ours, and a set_ptt, set_freq
or set_mode whose acknowledgement goes missing is verified by reading the rig
back instead of being reported as a failure. WSJT-X and JTDX answer a failed
command with a Rig Control Error and drop the link mid-over — 98 keyings, 6 lost
acknowledgements, 2 dropped connections in one session. The check waits 700 ms,
not the poll's 150: the rig has just failed to answer twice because it was
retuning, and a short probe would fail for the same reason.
Auto-call is withdrawn — it duplicated DXHunter, which already answers decodes,
and two programs deciding that from one shack key over each other. The library
is kept whole and dormant; a guard in App.tsx makes sure a stored preference
cannot key a transmitter whose switch no longer exists.
Also:
- the log rotates while running, not only at startup: the CI-V trace left on
wrote 416 MB and nothing would have stopped it before the disk did. Closing
it now releases the crash file too — the runtime keeps its own duplicate.
- the interface zoom announces itself, with a badge, a click back to 100% and
a View menu; Ctrl+wheel and Ctrl+0 always worked and nothing said so.
- no more elastic bounce, and no swipe-to-navigate out of the app.
- Edit QSO: your own TX power and the contacted station's extended locator
were saved and written back with no box to set them.
- FT decodes: continents are a multiple choice; a compound MSHV message that
answers two stations in one line is recognised as addressed to you.
Three faults an operator's log finally made visible, plus the interface
work that came out of the same session.
Reliability:
- UDP events were dropped on backpressure without a word. A period hands
over twenty-odd decodes at once, and one slow write to the radio was
enough to fill the queue — so a decode simply never appeared, and the
only detector was the operator comparing the panel with JTDX. The drop
is now counted and logged, panadapter spots went to their own goroutine
so the radio can no longer hold the decode stream up, and the queue is
deep enough for a full period.
- The CAT manager waited for its poll loop with a bare <-done. A loop
wedged in a serial read then blocked every later restart inside Start,
before it could even try to connect: the rig stayed dead, no line was
written anywhere, and only killing the process recovered it. The wait
is bounded at ten seconds and says what it abandoned and why the next
connect may fail.
- Shutdown had no logging at all, so a hang left nothing to go on and a
process the operator had to kill — which then blocked the restart after
an update. Every step is logged, and a watchdog forces the exit if one
of them never returns.
Auto-call:
- A QSO in progress is now held by OpsLog itself rather than inferred
from the sender's Status. The moment WSJT-X/JTDX dropped the DX call or
the Enable-Tx flag between overs, the exchange looked finished and the
next CQ was answered, interleaving two and then three QSOs on one
slice. Released on log, on halt, on taking over, and by a watchdog.
Cluster console:
- Replies to a command were buried under the spot flood; a Replies
toggle hides the DX spots, which the list above already shows.
- Twelve named command buttons beside the input, configured in
Settings -> Cluster; a button with no command is not drawn.
- Following the tail is now an explicit switch, and sending a command
re-arms it. It used to measure "am I at the bottom" AFTER committing
the new lines, so a ten-line reply looked like the operator had
scrolled up and was never followed — the one case it exists for.
Awards:
- An award can name NO field. The matching controls disappear with it
and only hand-assigned references count, which is the only thing that
can feed a reference like WWBOTA. A test pins that nothing else is
scanned.
- WWBOTA added to the catalogue with its 31 342 references.
Elsewhere: the rotor widget's Stop button acknowledges the press like
the direction presets already did, and the docked band map can be
switched to fit-to-band from its own header.
Extends to frequency and mode what PTT already had. A missing FB is not a
missing command: the rig acts on the frame as it decodes it, and what
expires is our wait for the answer, on a bus shared with the rig's own
transceive updates. JTDX in "Split: Fake It" moves the dial and the mode
immediately before every key-down, so those acks queue behind each other.
Losing one is fatal to the client rather than merely untidy: rigctld answers
RPRT -9, JTDX reads that as losing rig control and tears the connection down
mid-over. An operator's log shows three set_freq failures and one set_mode,
each followed within 300 ms by a fresh rigctld client -- and shows the PTT
resend rescuing an over that would otherwise have ended there.
Opt-in per caller rather than folded into exec: only a command that says
"be in this state" can be repeated safely, and a relative one must never
come through here.
The acknowledgement loss itself is still unexplained. Every failure in that
log is preceded by a state read reporting SSB on a rig in DATA, which points
at CI-V frame desync rather than a slow rig, and needs a trace to pin down.
"PTT via CAT does nothing on TCI." What OpsLog sends is right — trx:0,true; is
the documented command and the same one the reference clients send — so the
command was going out and the radio was discarding it.
ExpertSDR announces transmit permission with TX_ENABLE: on connect, and again
whenever the band changes, "in case transmitter permission was changed" (§4.3).
While it is false the radio simply IGNORES trx. OpsLog never read that command,
so there was nothing in the log, nothing on screen, and a dead key.
Now the permission is tracked and SetPTT refuses out loud, naming where to look:
the frequency must be inside a transmit band and TX enabled in ExpertSDR. The
refusal travels the path that already exists — Manager.SetPTT to pttKey, which
logs it and hands it to the UI.
Silence is not a "no". A radio that never mentions TX_ENABLE — an older
ExpertSDR, or another program speaking TCI — is not treated as refusing: we key
and let it decide. Permission is also forgotten on connect, so a refusal
remembered from a band since left cannot block PTT until a restart.
This may not be the operator's own cause, and that is the other half of the
change: if it is not, the log now settles it in one line. cat: TCI: → trx:0,true;
present means the command left OpsLog and the radio ignored it for a reason it
has not told us; absent means the fault is on this side.
Spot mirroring drew the same station two or three times, a few hertz apart.
Not a loop in the spot pipeline — one cluster line produces exactly one
SendSpot. It is that a popular DX station IS spotted two or three times, by
different operators inside the same minute, and no two of them agree on the
frequency to better than a few tens of hertz. This backend assumed ExpertSDR
replaced a spot bearing a callsign it already held, and said so in a comment;
it keys on the frequency too, so each of those became its own marker and stayed.
The FlexRadio backend has always done this properly (spot remove before spot
add, "one live spot per call"). TCI now does the same: the frequency drawn for
each call is remembered, a re-spot within 500 Hz sends nothing at all, and one
further away deletes the old marker before drawing the new one — so a station
that really moves still moves, instead of collecting markers.
SPOT_DELETE was not in the protocol document this backend was written from.
Confirmed before use against ars-ka0s/eesdr-tci, an independent TCI library that
lists SPOT with 5 arguments, SPOT_DELETE with 1 and SPOT_CLEAR with 0 — the
other two matching exactly what already works here, which is what makes the
third trustworthy.
The memory is cleared where Connect sends spot_clear. Left standing, it would
suppress the next spot for every remembered call as "already drawn" onto a
panorama the radio had just emptied — spots would quietly stop appearing after
a reconnect until each station changed frequency.
Five tests on the decision, which is split out from SendSpot so it can be
checked without a radio.
WSJT-X "Fake It" shifts the dial for the duration of each over and puts it
back afterwards, but the restore is conditional: it reads the frequency back
and only moves the dial if it disagrees with where it believes the radio
should be.
That read lands inside the window where this backend stops polling on
purpose. A Kenwood answers "?;" to IF; while it is transmitting, and treating
that as a fault used to drop the shared CAT link entirely, so the cached
state answers instead. SetFrequency wrote the command to the rig without
touching that cache — so mid-over the cache still described the pre-over
dial, WSJT-X read its own receive frequency back, concluded there was nothing
to restore, and the radio stayed on the transmit frequency. Every later over
started from there.
Reported from a session where the dial stuck at 7075500 after a full FT8
over while a bare TUNE, which never sets a frequency, worked fine.
Only simplex updates the cache. Under split, FreqHz is the transmit frequency
while the write lands on whichever VFO the operator is on, and guessing which
side moved would put a wrong number in front of the operator — a stale one
survives until the next poll.
The test reproduces the reported sequence and fails without the fix with the
same frequency the log shows.
set_split_vfo and set_split_freq both answered RPRT 0 and did nothing. WSJT-X
and JTDX in "Split Operating: Rig" send exactly that pair, believed both, and
transmitted on the RECEIVE frequency — on a pileup, straight onto the DX, while
showing the operator precisely what they had asked for. A lie that leaves no
trace in any log is the worst kind of bug this program can have.
The two commands are honoured as a PAIR. Arming alone does nothing on the radio,
because WSJT-X sends the frequency second and split armed on whatever the
transmit VFO happened to hold is worse than no split at all: it transmits
somewhere the operator never chose. The request is remembered and set_split_freq
does the work.
Kenwood gains SetSplit — FB to place the dial, then FR0/FT1 to arm, in that
order for the same reason. It writes what State() already knows how to read.
Everything else REFUSES, and that is the feature, not a shortfall. Only Flex and
Icom could even toggle split before, neither could set the transmit frequency,
and Yaesu, TCI and OmniRig have nothing at all. A refusal WSJT-X can report —
and act on, by falling back to Fake It — is worth far more than a success it has
no way to check.
Both paths are pinned: split reaching the rig as one armed call with the right
frequency, and a backend that cannot do it producing an error rather than RPRT 0.
IF reports the VFO "in use". In split that is the RECEIVE VFO while receiving
and the TRANSMIT VFO while transmitting — the backend took it as the receive VFO
in both cases. Everything therefore read correctly until the PTT closed and then
reversed, which is exactly how it was reported from a TS-590 on USB.
The IF frame has carried the transmit bit all along; parseKenwoodIF already
decoded it into f.TX. It was simply never consulted here.
This is not only a display fault. FreqHz is what a QSO is LOGGED on, so a
contact worked in split went into the log on the DX's frequency instead of the
operator's — wrong in the log, wrong in every ADIF exported from it, and
invisible until someone checked a QSO by hand.
The emulated rig in the test package can now be keyed, so the case is pinned
from both sides: verified failing without the fix (tx and rx exchanged) and
passing with it.
CW over CAT never worked on a Kenwood. The KY implementation was written against
Elecraft's, which accepts a string of any length, so "KY OH5CX;" went out and a
TS-590SG answered "?;". OpsLog read that as "this radio refuses CW over CAT" and
told the operator to fit a serial keyer — advice that was wrong, and expensive.
The TS-590 manual is explicit: P2 has a fixed length of 24, blanks are filled
with spaces, and those spaces are not keyed. So the fix costs nothing on air; it
is simply the shape the command has. Elecraft stays variable-length, where
padding would key the trailing spaces as word gaps.
The semicolon is also gone from the allowed CW characters. It TERMINATES a CAT
frame, the manual forbids it in P2, and one in a macro would have closed the
command early and left the rest of the message to be read as commands.
Found from a log and a manual page, not from a rig: nobody here owns a Kenwood.
What is proven is the frame shape; that a TS-590SG then keys it still needs the
operator to confirm.
A Kenwood answers "?;" while it is busy, and the TS-590SG does it for a moment
after RX; — which is exactly when the poll resumes. One rejected IF; then tore
down the whole CAT link.
The code already knew this. Its own comment says a "?;" to IF; is "a transient
busy, NOT unsupported" and that latching it off "would read as lost the rig".
That reasoning was applied to the unsupported-command map and stopped there: the
call still returned an error, the poll loop still turned it into connected=false,
and the link still dropped.
What it cost was not cosmetic. WSJT-X keys through shared CAT, so it lost the
rig mid-sequence; Hamlib then sent "F 9223372036854775808.000000" - an
uninitialised 2^63 - which OpsLog refused and logged. The operator sees a
frightening frequency error whose actual cause is three lines earlier.
A "?;" is now sentinel-wrapped so the poll can tell "the rig declined" from "the
serial link is gone", and three consecutive ones are ridden out on the last
known state before the link is called dead. Under a second of tolerance: enough
for the rig to finish, far too short to hide an unplugged cable. A serial fault
is untouched and still drops immediately.
Tested against the emulated rig already in this package, with a hook that
answers "?;" on demand: the link survives inside the grace and still reports the
last good frequency, the count resets on recovery so a later busy spell gets the
full allowance, and a rig refusing forever is still reported as broken.
MD6 is FSK on a Kenwood and DATA on a K3/K4. kenwoodModeToADIF decoded the
digit unconditionally as RTTY, so OpsLog contradicted the mode it had just
set: SetMode writes MD6 for a digital mode on an Elecraft, then ReadState
parsed the IF frame back as RTTY.
A K3 running FT8 therefore showed RTTY in the status bar, logged its QSOs on
RTTY, and — through the shared CAT server — told WSJT-X/JTDX the rig sat in
RTTY while they had just asked for a data mode. Found in a K3 operator's log:
every cat:state line read mode=RTTY on 21.074 FT8, two lines after OpsLog's
own "MD6;".
The digit now resolves to the configured digital mode whenever MD6 means DATA
on this rig — the Elecraft backend, and the "DATA A - MD6" data-mode option
that exists for it. A plain Kenwood still reads MD6 as RTTY.
The Elecraft handling was buried in the Kenwood "data mode" option, so users
couldn't find it. Add "Elecraft K3/K4" as its own entry in the CAT backend
selector. It reuses the Kenwood-dialect transport and the Kenwood USB/network
settings (the K3 emulates the Kenwood command set — a separate transport would be
a near-total duplicate), with an `elecraft` flag on the client that forces
digital modes to DATA A (MD6+DT0) — no data-mode dropdown needed. RigState still
reports Backend "kenwood" so the CW-over-CAT keyer capability keeps working.
Integrates the fix/jtdx-kenwood-tx work onto main: the Kenwood/Elecraft backend's
"data" data-mode path now sends MD6 then DT0 so a K3/K4 lands in DATA A — the
audio sub-mode FT8 uses. MD6 alone could leave the rig in an FSK/PSK sub-mode
where it keyed but the rear sound-card audio never modulated ("transmits but
nothing comes out"). The data-mode option is relabelled "DATA A — MD6+DT0
(Elecraft K3/K4)". A shared Kenwood/Elecraft backend is kept (the K3 emulates the
Kenwood dialect); the Elecraft specifics live behind the data-mode seam rather
than a 7000-line duplicate backend.
A K3 (and other Kenwood-dialect rigs) answers "?;" to an IF; status poll while
it is transmitting. ask() latched that as "IF unsupported" and ReadState
returned an error, so the Manager dropped the whole CAT link mid-transmit — the
log shows connected=false / "IF rejected" the instant JTDX sent TX;. That tore
down the shared rigctld CAT the digital-mode software keys through.
Two fixes: (1) track PTT (SetPTT) and skip the wire poll while it's held —
ReadState hands back the cached last state, capped at 30 s so a missed
SetPTT(false) can't freeze it; (2) never latch IF/ID as unsupported — those are
universal on Kenwood/Elecraft, so a "?;" to them is a transient busy (mid-TX),
not a missing command.
No single Kenwood mode digit fits every rig for a data mode: a K3/K4 wants
DATA (MD6), a TS-590SG/TS-990S data mode is a USB modifier set on the rig,
and MD6 on a plain Kenwood is FSK/RTTY. So the operator now chooses in
Settings → CAT: USB (default), DATA (MD6), or leave the rig's mode unchanged.
Only soundcard/data modes (FT8, PSK, JT…) follow this; RTTY/FSK stays its own
native mode, and voice/CW are untouched (isKenwoodDataMode + test).
The frontend engine loader had no "kenwood" case, so a saved engine of
"kenwood" fell through to the WinKeyer default — the Kenwood/Elecraft
CW-over-CAT engine never ran even though the setting showed it selected.
Also clarify the Kenwood data-mode comment: there is no single mode digit
right for both a K3 (DATA=MD6) and a TS-590SG (MD6=FSK), so data stays on
USB as the safe common base; a rig-specific DATA mode is a follow-up.
- PGXL: remote AUTH password; direct-link meter fallback (VITA-first) with
250 ms poll + peak-hold; fan mode uses bare "fanmode=" (was ignored).
- TCI: spot colour sent as decimal ARGB (ExpertSDR dropped the hex string);
spot click handled via CLICKED_ON_SPOT / RX_CLICKED_ON_SPOT to fill the entry.
- FlexRadio: clicking an OpsLog spot on the panadapter now applies the mode too.
- Filter presets: the trash icon deletes again (Radix pointer-down intercept).
- PTT hotkey: keys over CAT when a backend is active (was hijacked by a stale
Audio-tab RTS/DTR serial setting); AltGr keys allowed; presses logged.
- CW macro <LOGQSO>: logs after the preceding CW is sent, not on the first letter.
Settings -> Rotator is now a list like the amplifiers: add/remove rotors,
mix PstRotator / Rotator Genius / ARCO, and a Rotator Genius can drive both
its ports (one entry = two rotors). The compass gains a rotor selector, and
a per-rotor motorized-antenna flag so the boom/pattern paths show only for
the rotor carrying the Ultrabeam/SteppIR.
Also in this batch: a keyboard PTT hotkey (hold-to-talk or toggle, reusing
the audio PTT method with a CAT fallback), and TCI spot push to the
panadapter with click-to-fill of the callsign.
rouggy