Confirmed from an FT-891 CAT log: OpsLog tuned via OmniRig's SetSimplexMode,
which returned OK on every spot click but never moved the VFO (readback stayed
put), while SetMode on the same .ini worked — so the CAT link was healthy and
only the frequency write was a no-op. SetSimplexMode was chosen because Icoms
accept direct FreqA writes but don't move; Yaesu/Kenwood are the opposite.
Now, for non-Icom rigs (or if SetSimplexMode errors), also write the VFO
frequency property (FreqA/Freq) directly, which does move them. Icom keeps the
SetSimplexMode-only path so the Main/Sub VFO isn't nudged by a direct write.
Some CW interfaces key on the opposite line level (transmit at rest / key
backwards). New "Invert keying (active-LOW)" toggle flips the asserted level for
both the CW and PTT lines, and the idle state drives both lines to their
inactive level accordingly so an active-low rig isn't left keyed at rest.
Default off = N1MM convention (line HIGH = active).
Adds a 4th CW keyer engine alongside K1EL WinKeyer, Icom CI-V and Flex CWX:
OpsLog bit-bangs the Morse itself on a serial control line (DTR keys CW, RTS
keys PTT — swappable), the hardware-keying method N1MM/WSJT use with a Yaesu
SCU-17 and generic interfaces. No WinKeyer chip needed.
- internal/winkeyer/serialcw.go: serialKeyer — worker goroutine, morse table,
WPM + Farnsworth timing (live speed changes), abortable, PTT lead-in/tail/hang.
- winkeyer.Config gains Type ("k1el"|"serial") + CWKeyLine ("dtr"|"rts");
Manager routes Connect/Send/Stop/SetSpeed/Backspace/Disconnect to it.
- app.go: keyWKCWLine setting; WinkeyerConnect sets Type from the engine.
- Settings -> CW Keyer: new "Serial port (DTR=CW/RTS=PTT)" engine with COM port,
key-line selector, speed/Farnsworth/lead-in/tail/PTT. Macros, auto-CQ and
<LOGQSO> reuse the WinKeyer path unchanged.
UNTESTED on hardware (no SCU-17 to hand): polarity assumes N1MM convention
(line HIGH = active). Weight not yet honoured; Farnsworth is.
The rig's 0x27 waveform frames carry the same leading main-scope selector byte
as the dual-scope IC-7610/9700 (`27 00 00 <seq> <total> …`), but the code keyed
the layout off the CI-V address and treated the 7300 as selector-less, reading
the sequence from Data[1] (always 0x00) so every frame hit the `seq == 0`
guard and was dropped — blank scope. The waveform parser now detects the
leading selector byte from the frame itself (address-independent), and the
scope config/set commands (mode, span, edges) include the selector the 7300
requires. The IC-7610/9700 path is byte-for-byte unchanged (main → idx 2, sub
frames skipped). Confirmed against a real IC-7300 CI-V capture.
0.20.10 was released before the "closing OpsLog switches off the radio's own
scope" fix landed, so its entry is reattributed to 0.20.11 (the fix code is
already committed in 1668455).
SetScope(false) sent both 0x27 0x10 00 (scope DISPLAY off) and 0x27 0x11 00
(CI-V data output off), so quitting OpsLog blanked a local IC-7300's own scope
screen. Only the display-on (0x27 0x10 01) is now sent, and only on enable;
disable stops the CI-V stream alone and never touches the radio's display.
The multi-frame waveform header (USB path) read the second frequency field
as an absolute high edge, but in center mode it is a span — so high < low and
the panadapter had no valid range to map the trace onto (blank scope). It now
applies the same center+span vs low+high disambiguation the IC-7610 single-
frame path already used. FIXED mode was unaffected.
Also stamps changelog 0.20.10 with today's date.
- Station Control: the amplifier panel is now the exact same card as the FlexRadio panel (extracted shared AmpCard: OPERATE/STANDBY, ON/OFF, power level, output-power bar, live FWD/ID/temp meters). Every configured amp gets its own card — no dropdown.
- Help → "Send log to F4BPO" (only when SMTP is configured): e-mails opslog.log + previous session + crash log to the developer. New email.SendFiles for multi-attachment.
- Bulk edit: new "Frequency (MHz)" field sets freq_hz AND recomputes band; out-of-band values rejected. Fixes a run logged on a stale/default freq after CAT dropped.
- Cluster: Time column sorted lexically on the HHMMZ string, so spots after 0000Z sorted below 2359Z and looked frozen at the UTC rollover. Now sorts by real arrival time.
- Also folds in the DVK auto-CQ/2-column layout and Station Control dashboard batch (changelog 0.20.10, EN+FR).
Multi-amp: Settings->Amplifier becomes a list (amps.json, legacy single-amp keys auto-migrate to entry #1); one client per enabled amp with per-id bindings (GetAmplifiers/SaveAmplifiers/GetAmpStatuses/AmpOperate/AmpPower/AmpPowerLevel/AmpFanMode); legacy a.pgxl/a.spe/a.acom point at the first enabled amp of each family. Amp cards in FlexPanel and Station Control gain a dropdown to pick the amp; the status bar shows one clickable chip per amp. Use case: two SPEs run in parallel.
Flex v4 DSP (8000/Aurora): NRL/ANFL (lms_nr/lms_anf), NRS (speex_nr), NRF (nrf) with level sliders, RNN (rnnoise) and ANFT on/off — keys per the FlexLib slice docs; the section only shows when the radio reports these keys (dsp_v4 flag), so 6000-series panels are unchanged.
The station-control code rebuilt a fresh driver on every status poll and every
relay set. Stateful boards (Denkovi FTDI D2XX, USB-serial) hold an OS handle only
one opener can own, so the first poll opened the board and leaked the handle, and
every poll after failed with 'device in use' — the relays greyed out a second
after Save and auto-control never switched. Drivers are now cached per device and
reused, closed on config change. Adds a Test-connection button + detect feedback
in the device editor (reported by VK4MA).
rouggy