Confirmed from an FT-891 CAT log: OpsLog tuned via OmniRig's SetSimplexMode,
which returned OK on every spot click but never moved the VFO (readback stayed
put), while SetMode on the same .ini worked — so the CAT link was healthy and
only the frequency write was a no-op. SetSimplexMode was chosen because Icoms
accept direct FreqA writes but don't move; Yaesu/Kenwood are the opposite.
Now, for non-Icom rigs (or if SetSimplexMode errors), also write the VFO
frequency property (FreqA/Freq) directly, which does move them. Icom keeps the
SetSimplexMode-only path so the Main/Sub VFO isn't nudged by a direct write.
The rig's 0x27 waveform frames carry the same leading main-scope selector byte
as the dual-scope IC-7610/9700 (`27 00 00 <seq> <total> …`), but the code keyed
the layout off the CI-V address and treated the 7300 as selector-less, reading
the sequence from Data[1] (always 0x00) so every frame hit the `seq == 0`
guard and was dropped — blank scope. The waveform parser now detects the
leading selector byte from the frame itself (address-independent), and the
scope config/set commands (mode, span, edges) include the selector the 7300
requires. The IC-7610/9700 path is byte-for-byte unchanged (main → idx 2, sub
frames skipped). Confirmed against a real IC-7300 CI-V capture.
SetScope(false) sent both 0x27 0x10 00 (scope DISPLAY off) and 0x27 0x11 00
(CI-V data output off), so quitting OpsLog blanked a local IC-7300's own scope
screen. Only the display-on (0x27 0x10 01) is now sent, and only on enable;
disable stops the CI-V stream alone and never touches the radio's display.
The multi-frame waveform header (USB path) read the second frequency field
as an absolute high edge, but in center mode it is a span — so high < low and
the panadapter had no valid range to map the trace onto (blank scope). It now
applies the same center+span vs low+high disambiguation the IC-7610 single-
frame path already used. FIXED mode was unaffected.
Also stamps changelog 0.20.10 with today's date.
Multi-amp: Settings->Amplifier becomes a list (amps.json, legacy single-amp keys auto-migrate to entry #1); one client per enabled amp with per-id bindings (GetAmplifiers/SaveAmplifiers/GetAmpStatuses/AmpOperate/AmpPower/AmpPowerLevel/AmpFanMode); legacy a.pgxl/a.spe/a.acom point at the first enabled amp of each family. Amp cards in FlexPanel and Station Control gain a dropdown to pick the amp; the status bar shows one clickable chip per amp. Use case: two SPEs run in parallel.
Flex v4 DSP (8000/Aurora): NRL/ANFL (lms_nr/lms_anf), NRS (speex_nr), NRF (nrf) with level sliders, RNN (rnnoise) and ANFT on/off — keys per the FlexLib slice docs; the section only shows when the radio reports these keys (dsp_v4 flag), so 6000-series panels are unchanged.
Completes the CWX type-ahead loop: with send-on-type the keyer-panel CW text
already streams each typed char to the radio's CWX buffer (which keys in order,
so you can keep typing while it sends); this adds the matching un-send. Route
wkBackspace to FlexBackspaceCW -> cwx erase N, so backspacing a mistyped char in
send-on-type removes it from the buffer before the radio keys it.
The 7610-only FreqA gate broke CAT on the 7610 when FreqA was momentarily 0.
Match DXHunter/WSJT-X: read FreqA first for all rigs, fall back to the generic
Freq (IC-9100 etc.), then FreqB. OmniRig's generic Freq maps to VFO B on the
7610, which is why keying off FreqA is correct.
OmniRig: on the IC-7610 the generic Freq property reports the wrong VFO (its
Main/Sub model confuses the stock ini), so OpsLog showed VFO B. Detect the rig
by RigType and, in simplex, read VFO A explicitly — matching Log4OM. Only the
7610 is affected; other rigs keep using the generic Freq.
Icom network: when the rig tears the session down (control/CI-V 0x05) OpsLog
only logged it and kept the half-dead link until the 6 s liveness timeout
expired. Mark the link dead on 0x05 so Alive() fails on the next poll and the
manager reconnects cleanly right away.
rouggy