56 lines
2.5 KiB
Markdown
56 lines
2.5 KiB
Markdown
# Icom
|
|
|
|
When the CAT backend is **Icom CI-V** (USB or network), OpsLog shows a full
|
|
RS-BA1-style console — the same panel whether you're on USB or remote.
|
|
|
|
For setup, see [[CAT Control]]; for the internet link, see
|
|
[[Remote Icom over the Internet]].
|
|
|
|
## Choosing your model
|
|
|
|
Pick your model from the **Rig model** dropdown in Settings → CAT — it sets the
|
|
CI-V address and tailors the console to the radio (e.g. attenuator steps).
|
|
The model is also auto-detected from the radio's CI-V ID.
|
|
|
|
## Console
|
|
|
|
- **Twin VFO readout** (MAIN / SUB): big tabular frequency, mode badge, band, and
|
|
RIT/ΔTX offset, with a **mode-button row** (SSB / CW / RTTY / PSK / AM / FM).
|
|
- **Spectrum scope + waterfall**: ON/OFF, CTR/FIX, double-click to tune, and
|
|
**◀ ⊙ ▶** to centre the scope on the current frequency (±50 kHz) and pan.
|
|
- **Live meters** always visible: S-meter (click → fill RST), power in watts, SWR.
|
|
- **Receive DSP:** AF / RF gain, squelch, AGC, preamp, **attenuator** (steps match
|
|
the model — e.g. 20 dB on an IC-7300, 6/12/18 dB on an IC-7610), filter
|
|
(FIL1/2/3), NB, NR, ANF, and — **on CW only** — the **APF** (audio peak filter).
|
|
- **Passband / notch:** Twin PBT (inner / outer) and manual notch + position.
|
|
- **Transmit:** RF power, MOX, TUNE, **split with automatic offset** (+5 kHz SSB /
|
|
+1 kHz CW), monitor. On **voice modes only**: mic gain, compressor, VOX (+ gain
|
|
+ anti-VOX). Controls that don't apply to the current mode are hidden.
|
|
- **Bands & antenna:** one-touch band buttons, ANT1/ANT2.
|
|
- **Clarifiers:** RIT and ΔTX, wheel / ± tuning (Ctrl + ← / → nudges RIT).
|
|
|
|
## Power ON / OFF
|
|
|
|
- **Network:** ON and OFF buttons are shown — the radio's LAN server answers even
|
|
in standby, so ON works.
|
|
- **USB:** the buttons are **hidden**. Over USB the CI-V interface is unpowered
|
|
while the rig is off, so a power-ON command can't reach it — turn the radio on
|
|
physically.
|
|
|
|
The app never wakes the rig on connect (manual by design).
|
|
|
|
## CW keying
|
|
|
|
CW can run through the **radio's own keyer** over CI-V — no extra hardware, and
|
|
it works over the remote link too. See [[Audio and Keyers]].
|
|
|
|
## Model-specific notes
|
|
|
|
- **IC-7300 / IC-705 / IC-9100:** single-receiver, single-step attenuator
|
|
(20 dB); the IC-9100 is USB-only (no LAN server).
|
|
- **IC-7610 / IC-9700:** dual scope (main/sub); stepped attenuator; LAN server
|
|
for remote.
|
|
- If the **scope is blank on a single-scope rig run at a non-default CI-V
|
|
address**, OpsLog now detects the model from the CI-V ID, not the configured
|
|
address, so it decodes single-scope frames correctly.
|