The log settles it, and it was not mute. Mute works: '→ mute:0,true;' and
the radio answers 'mute:0,true'. What happens is that the squelch REFUSES
to go off — we send 'sql_enable:0,false;', the radio echoes false, and
eighty milliseconds later announces 'sql_enable:0,true' again. Six times
in the log, always the same shape. The SQL lamp coming back on right after
a MUTE click is that revert landing, not the mute doing it.
So the optimistic hold is fixed rather than the phantom. It was a fixed
1.2 s, which is wrong in both directions: too short for a setting the
radio never echoes at all (AGC), and too long for one it refuses, where it
showed the operator a lie for a second. The requested value now stands
while the radio says nothing about that setting, and the instant the radio
reports any change for it, its word replaces ours. A refusal is therefore
visible immediately, and an unechoed setting still sticks.
Also from the same session: filters per MODE — the narrow end in CW, the
voice widths in SSB, a middle set for the digital modes — because 250 Hz
in SSB and 2.8 kHz in CW are buttons nobody presses. And APF is shown only
in CW: it rings a single tone out of the noise, which is a CW tool and
nothing else.
250 now means 0-250. It meant 575-825: the width was right and it was
centred on the CW note, on the reasoning that a CW filter should contain
the note. That reasoning may be right for a radio and it is still wrong
here, because it is not what the button says — and a button that does not
do what it says is worse than one that does something simple. The two
edges are editable underneath for anything else, which is what TCI takes
anyway.
And MUTE still lights the squelch on a real radio. Nothing in this code
can do that — the button sends mute and only mute, and the two are
separate state — so the radio's own announcements are logged as they
arrive. What it says after the command will settle whether this is our
reading or its doing; no more reasoning from here will.
Three things reported from the radio, all of them mine.
THE LEVELS. Two half-width sliders side by side left each of them a couple
of centimetres long, which is not enough to set 15% with. One level per
row now, full width, with the value typed in or stepped with ± — and in
the radio's own units, so the volume is dB and the squelch a dBm
threshold, matching what ExpertSDR3's own window shows.
THE FILTERS. The button said 250 and the radio was set to 300-550: 250 Hz
wide, but sitting where no CW note is. The edges are computed from the
width now, and a narrow filter is CENTRED ON THE CW NOTE — a 250 Hz filter
from 100 to 350 would put the note outside its own passband. A button also
lights on the WIDTH the radio reports rather than on an exact pair of
edges, so moving one edge on the radio no longer darkens every button.
MUTE. Read from one shape only, while this radio reports the other
('mute:0,false'), so the button showed the opposite of the truth. Both are
accepted now.
None of this should have reached main before somebody had a radio in front
of it.
Two faults, reported from a real SunSDR.
DRIVE AND TUNE DRIVE DID NOTHING, and neither did MUTE. Those commands
carry the transceiver index — 'drive:0,15;', not 'drive:15;' — and sent
without it the radio ignores them silently: no error, no answer, the power
unchanged. The rule was in the radio's own reports all along, which is
where it should have been read from: it announces 'drive:0,85' and
'mute:0,false' at connect, while 'mic_level:100' and 'volume:-12' come
with no index at all. Sending the shape the radio speaks in is the whole
rule, and it is now written down next to the two exceptions.
AGC LOOKED STUCK ON SLOW. The panel showed only what the radio reported
back, on the principle that the radio is the truth — but ExpertSDR3 does
not echo every setting it accepts, so a working button sat unlit. Changes
are shown at once and held for a moment now; whatever the radio announces
afterwards still wins, so a clamped or refused setting stays honest
without every working one looking broken.
Also from the same report, and fair: the consoles did not resemble each
other. The Icom panel's RIT control is now a shared component both use —
chip, signed offset, ± keys, wheel, and TYPING a value straight in, which
is the thing a row of ±10/±100 buttons cannot do. Ctrl+←/→ shifts the RIT
here as it does there. And LONG is gone from the AGC row: the protocol
takes it, but it is a hang time nobody reaches for between overs.
Adding it to the device lists put it in all four dropdowns, and an
operator picked it as their RECORDING MIC — which would have recorded the
station they were listening to instead of their own voice, on every voice
message and every QSO recording. It is not a microphone, and it is not a
pair of speakers either: the audio going the other way is transmit audio.
So it is listed for 'From radio' and 'To radio', and taken out of the mic
and the listening dropdowns.
And the RX monitor is disabled when the radio IS the source, with a line
saying why: the TCI stream is pushed into the QSO recorder, and nothing
plays it to the speakers. The button was there, enabled, doing nothing
audible — which is worse than a button that says it cannot.
TCI already carries the frequency, the mode, the meters and now the audio.
It also carries everything else about the radio — and OpsLog was logging
most of it once as '(unhandled once)' and throwing it away. The console is
mostly a place to put what was already arriving.
That makes it the cheapest panel here, and it is worth saying why. A K3
console costs a command and a reply for every value it shows, which is why
it reads its settings in a rotation and its meters only while on screen.
TCI PUSHES: the radio announces its drive, its filters, its noise blanker
and the rest on connect, and again whenever any of them changes —
including when the operator changes them in ExpertSDR3's own window, which
this panel therefore follows without asking anything.
What it drives: drive and tune drive, mic gain, TUNE, volume, mute,
squelch and its threshold, NB, NR, ANF, APF, AGC speed, the passband, RIT
and XIT with their offsets, and the VFO lock. The S-meter is a real dBm
reading, so its S units are arithmetic rather than the calibration guess a
K3's meter needs.
Setters never update the cached state. The radio answers with the new
value, and taking its word is what keeps the panel honest when a setting
is refused, clamped, or changed at the radio a second later — the one
exception being a slider mid-drag, held for 900 ms so it is not dragged
back by its own echo.
Capped width and centred, like the other consoles. Also offered as a
docked pane — and the Elecraft console is offered there too now: App has
always had that pane, Settings simply never listed it.
Reported on an Ultrabeam over USB: the port could not be chosen from the
dropdown, and the panel would not scroll.
That field was a Combobox — a list you can also type into — chosen so the
port of an adapter currently UNPLUGGED could still be configured. It is
now the same Select every other serial device in OpsLog uses, the one that
demonstrably works. The case it was built for is kept differently: a
configured port that is no longer detected is added to the list, so it
stays selected and visible instead of vanishing when the adapter is out.
Also hardened the Test button's guard, which called .trim() straight on
the port and the host. A settings object without them — an older build, a
save that landed short — throws there DURING RENDER, and a panel that
throws while rendering is exactly a panel with a dead dropdown that will
not scroll. Whether or not that is what this operator hit, it is a way to
produce both symptoms at once and it costs nothing to remove.
Reported with a screenshot: the map came up with API KEY REQUIRED written
twice across the middle of it, on the Light and Voyager views only. Those
are exactly the two Carto basemaps.
Nothing here could have caught it. The tiles still answer 200 with a real
image — the watermark is IN the image — so the map looks like it is
working and simply says otherwise in large grey letters.
Both views move to Esri, which is already behind Street and Satellite. That
is the point: a second key-free provider is a second chance to be cut off,
and this is now the third time a tile source has changed its terms under
us. Light is Esri's light canvas with its own label layer, and Voyager
becomes the topographic map, labelled Topo — the stored key stays
'voyager' so nobody who chose it is quietly moved somewhere else.
The canvas runs out of tiles at zoom 16 where the others go to 19, so
maxNativeZoom is set per basemap: Leaflet upscales the last real tile
instead of asking for a level that does not exist, which is the difference
between a slightly soft map and a blank grey square.
Telling somebody's amplifier where to be is a write to their station, and
it now has a switch — the SAME switch an Acom uses. 'Keep the amplifier on
the radio's band' is one idea to an operator; that it needs a second
serial port and a rig emulator on one amplifier and a single ^BN on
another is our business, not a reason for two checkboxes.
On by default for a KPA, because an amplifier left on the wrong band is
the worse outcome of the two, and the operator who has wired it straight
to the radio turns it off once. The hint says exactly that case, since it
is the only one where a second voice telling the amplifier where to be is
unwelcome.
Two things the wiring got wrong, both visible on screen.
A KPA fell through to the PowerGenius branch of the amplifier card and was
drawn as one — titled 'POWERGENIUSXL · ELECRAFT KPA1500', with a
PowerGenius's meters and none of its own. It has a card now: OPERATE, ON
and OFF, band, power, SWR, temperature, supply, and the fault across the
end. The OPERATE button carries a tooltip saying it also clears the fault,
because that is the button an operator already has under the cursor when
they need it.
And the band-follow option was offered on it. That option exists because
an Acom POLLS a transceiver and has no command to be given a band, so
following it needs a second serial port and a rig emulator answering those
polls. The KPA has ^BN — OpsLog simply tells it, on the link it is already
using, and only when the band CHANGES. The option is gone from the KPA and
the telling is automatic.
Also: Acom rather than ACOM everywhere it is read, which is how the
company writes it. Identifiers, package names and log lines are left
alone — renaming those is churn with no reader.
Wired into the multi-amplifier support that already carries the SPE, the
ACOM and the PowerGenius: a fourth brand rather than a fourth mechanism.
The linking, the fan-out and the poll all work on it unchanged.
Three things the KPA does differently, and each is handled where it shows
rather than explained in a hint:
- A KPA500 has no network side at all. Choosing it puts the entry on
serial, and a configuration still asking for TCP is refused with a
line saying so instead of retrying an address that cannot answer.
- The amplifier answers ^ON while its main supplies are OFF — a sleeping
microcontroller stays awake for exactly that — so power-on stays
available over the network, unlike the SPE and ACOM which need their
serial control lines.
- Going to OPERATE clears the current fault, everything except
temperature. The widget says so under the fault, because the button
that fixes it is the one already on screen.
Defaults that leave a working configuration when the model is changed:
38400 baud, TCP port 1500, and a full-scale power mark of 500 or 1500 W
by model — a KPA500 read against a 1500 W scale looks idle at full
output.
The columns took the award's declared band list when it had one, so every
band the award PERMITS got a column whether or not anything had ever been
worked on it. DDFM permits 6m and 70cm; a station that has never worked a
French department on either was shown two empty columns, which reads as a
gap in the log rather than as a band nobody tried.
They now follow the bands this operator actually has contacts on for the
award. The declared list is the fallback for an award with nothing worked
yet — there, saying what the award is played on is the only honest answer
available — and the classic HF set is the fallback for an award that
declares nothing either.
Together with taking the order from the full band list, this is what puts
23cm on DDFM: the column appears because there are contacts on it.
The columns were the intersection of the award's bands with a fixed list
that ended at 70cm, so a band the award genuinely covers could not appear
whatever it said. DDFM is worked well into the microwaves and had no 23cm
column, and nothing anywhere would have produced one.
The intersection is now taken against every band in frequency order, the
same list internal/award already sorts its own band counts by. The classic
HF-plus-2m-and-70cm set stays as the fallback for an award with no band
list and no contacts yet — the full list would be twenty-nine columns of
mostly nothing.
Two faults, and the first was a design mistake of mine.
The choice was written only as the award override, to keep the imported
CNTY as a record of what HAMLOG said. But CNTY is what the comparison
READS, so the contact went on disagreeing for ever: settle a hundred
rows, run the comparison again, get the same hundred back. The reasoning
was about preserving evidence; the effect was a button with no visible
consequence anywhere, which is indistinguishable from one that does
nothing. This is the operator's own log, and correcting a field in it is
the point of the exercise. The district now lands in CNTY as well as in
the award reference.
And the settled rows stayed on screen, which made the same button look
broken a second time. They are dropped as they are applied — locally,
rather than by re-running the comparison, which reads the whole log and
would be seconds of silence on a remote database to be told what is
already known. The agree/disagree counters follow.
The comparison could show two hundred contacts where the log and the
database name different districts, and leave the operator with nothing to
do about any of them but open each QSO and edit it by hand.
Now each row carries the two values as buttons: click the district you
keep, then apply. There are shortcuts for keeping one source everywhere,
and applying is a separate act — clicking through two hundred rows with
each one written as it is clicked would make a slip permanent before the
reading was finished.
The choice is written as the contact's AWARD REFERENCE, not over the
imported CNTY, and that distinction is the point. CNTY is what the
downloaded log said; overwriting it would destroy the evidence the
comparison runs on, and the next comparison would agree with itself and
prove nothing. The override is the operator's decision, it is what the
award engine counts, and it beats both sources. So the log keeps saying
what it said, the database keeps saying what it says, and the contact
counts for the district that was chosen.
The buttons show the districts themselves rather than a tick box: someone
arbitrating between RO-19 and KO-05 should be picking a value they can
read, not remembering which source a checked box stood for.
The TCI section of the audio settings was an investigation: open the
stream, read what arrives, record ten seconds to listen to, key a tone.
It answered every question it was built for — the frame layout, the
sample width, that the radio asks rather than follows a clock, that the
transmit audio source decides — and confirmed 80 W on real hardware.
None of that belongs in front of an operator now. The radio is simply one
of the devices in the two dropdowns, and choosing it IS the configuration:
one control, in the place where the question is already being asked.
Keeping the tick box beside it would have been two switches for one
decision, with the second one where nobody looks.
Gone with it: the stream/record/probe bindings, the audio.tci_rx setting,
and twenty-four translation keys. The plumbing they proved out stays and
now carries the voice keyer.
The RDA and Elecraft SWR entries move with it: both were written after
v0.26.14 was tagged, so they ship in the version that carries them rather
than in the one already on operators' machines.
A SunSDR carries its audio on the same WebSocket as its commands, so
OpsLog can take it directly: no virtual cable, no second sound card, no
Windows mixer between the recording and the air. The radio appears as a
device in both audio lists and can be chosen for either direction.
Everything here was settled on real hardware over one evening, and none of
it was guessable from the documentation:
- The receive stream answers format=3 for four-byte floats, so the
sample width is derived from the frame rather than trusted from the
field.
- The radio asks for transmit audio only when the transmission is the
CLIENT'S, and only when its transmit audio source is TCI rather than
the microphone.
- The chrono is a REQUEST, not a clock: no payload, carrying the size it
wants, 47 times a second. Audio goes out in answer to it and never on
a timer of our own — a timer was the first attempt and all 234 frames
of it were ignored.
Confirmed: a clean test recording, and 80 W out of a 1 kHz tone.
A first real transmission settled one question and raised a better one.
With the receive stream open and six seconds of transmit, the radio sent
282 frames of receive audio and NOTHING else: no chrono, no transmit
audio. So the chrono the documentation describes is not offered to a
client that merely happens to be connected while the operator keys the
microphone, and waiting for it to appear is waiting for nothing.
The reading that fits is that the radio asks for audio when the
transmission is the CLIENT'S and takes the microphone when it is the
operator's — which makes the experiment obvious. Key it from here, push a
1 kHz tone, and watch. Chrono frames appearing gives their size and
cadence by measurement instead of by guesswork; no chrono but a tone on
the meter is just as useful, because then the pacing is optional and the
voice keyer can push frames at the rate the stream already runs at.
A tone rather than silence so the answer shows on the power meter and not
only in the log.
It transmits, so: an explicit button inside a warning box, five seconds,
capped at ten, and every path out unkeys — including the panic that has
not happened yet and a socket that dies mid-tone. A transmitter left keyed
by a defect is the one fault here that would reach somebody else's band.
Writes are now serialised too. send() held the lock only long enough to
read the connection, which was enough while every command came from the
poll loop; a stream of audio frames from a second goroutine is not, and
gorilla panics on a concurrent write rather than failing quietly.
Two faults, one behind the other.
RDAPanel is nested inside SettingsModal so it can read its state, and it
was written as <RDAPanel />. A nested function is a new component TYPE on
every render: React cannot know it is the same panel, so it unmounted the
tree and mounted a fresh one — and a fresh scroll container starts at the
top. It is called now, like the other panels, which produces the same
elements in place and never disturbs the scroll position.
What it was reacting to should not have reached it either. The PSK
Reporter and grid-cache poll ran every three seconds from wherever you
were in Preferences, re-rendering the whole dialog for a count shown only
on the cluster section. It now runs while that section is open, and the
one-time loads it was sharing an effect with have stayed where they were
rather than refetching on every click in the sidebar.
The visible result: a hundred contacts to correct can be read from top to
bottom.
Confirmed on a real SunSDR: the stream decodes and the test recording
plays back clean. So it can do the job a virtual audio cable was doing —
this wires it to the QSO recorder, which already accepts a pushed source
(the Icom network audio uses the same door).
The conversion lives here rather than in internal/cat: the radio's job is
to hand over what it sent, not to know that the recorder works in 16 kHz
mono. Three samples are AVERAGED rather than two of them dropped —
decimating by picking every third folds everything above 8 kHz back into
the voice band, and on a receiver that is hiss, which a QSO recording has
plenty of already.
Off by default, and applied the moment it is switched: it replaces a
sound card the operator has already wired up, and an option that needs a
restart to take effect reads as an option that does not work.
TWO FAULTS, ONE SYMPTOM — 'it refreshes ten times a second and the
buttons cannot be pressed'.
Preferences is a child of the main view, so every cluster spot, CAT push
and decode re-rendered the entire panel. On a busy evening that is
several times a second, and the panel is large enough that the rebuild
outlasts the gap between them: buttons missed their clicks because the
element under the pointer was replaced between the press and the release.
It is memoised now, and the callbacks App hands it hold their identity —
without that the memo compares unequal every time and buys nothing.
The dropdown menu was an absolutely-positioned child, so it was clipped
by whichever scrolling or overflow-hidden box it sat in: the satellite
list showed one entry of eight. It is portalled to the body now,
positioned from the field's rectangle, re-measured while open, and opens
upward when the field is near the bottom of the screen — which is exactly
where these fields tend to be.
It has been a combobox since it was written, but without showToggle it
opens only on a keystroke or ArrowDown — both of which have to be known
about first. On screen it is a text box, which is exactly what 'still no
dropdown' meant.
allowFreeText with it: the list is the station's own, so a bird worked
once and never added must still be loggable.
SATELLITES: the field read the list once, when the details panel first
mounted — which is at startup. A list saved in Preferences afterwards
therefore did nothing until a restart. It comes from App now, which
already reloads the lists when Preferences close.
RDA COMPARE: a failed comparison wrote its error into the message beside
the FILL DISTRICTS button, a row above — the error appeared under a
button nobody had pressed while the one that had been pressed showed
nothing, which reads as 'the button does nothing'. It has its own message
now, and reports the two results that look like silence: no disagreement
at all, and no Russian contacts to compare. Both buttons say what they
are doing while they do it, and the comparison logs before it starts
reading — on a remote MySQL that read is seconds of quiet.
overscroll-contain on the conflict box stops the wheel from chaining to
the pane behind it. With a short list — nothing to scroll inside the box
— the pointer over the table therefore froze the whole panel: the page
would not move and neither would the list.
The box scrolls when it has something to scroll; the page scrolls the
rest of the time, which is what containment was preventing.
Save builds the lists payload field by field, and the new list was not
among them — so every Save wrote an empty satellites array over whatever
had just been typed.
Normalised in the save as well as on the field's blur: the Save button is
reachable without ever leaving the box, and a list whose survival depends
on where the cursor went first is a list that saves sometimes.
SAT_NAME is compared character for character by the awards and by LoTW:
AO-91 and AO91 are two different satellites to everything downstream, and
typing it afresh on every pass is how one of them ends up in a log. So
the station keeps its own list (Preferences → Lists → Satellites) and the
field offers it, alphabetically — while still accepting anything typed,
because a bird worked once and never added to the list must not be
impossible to log.
Not seeded with a shipped list of two dozen birds: an empty list means
this station does not work satellites, and filling the dropdown with
names nobody here has heard makes the field harder to use, not easier.
Also fixes the RDA district comparison: its conflict list was capped at
about six visible rows of a list holding up to two hundred, in a panel
that would not scroll to show the rest, and nothing in it could be acted
on. Taller, scrolling, and a callsign opens the contact.
Three wide buttons for something most radios cannot vary was noise, and
they pushed the fields below into whichever grid column came next — the
panel looked shuffled.
Now: a dropdown, shown only when the brand has more than one way in. A
Yaesu is reached over USB and that is the end of it; a control offering
one entry that cannot be changed is a decision that is not one.
Brands: OmniRig first — it is the one that works with any radio, so it is
where someone who cannot find their rig should land — then alphabetical.
Kenwood and Elecraft drop the proprietary-network entry: neither is
implemented and neither is planned, and naming a road that goes nowhere
is only useful when someone might reasonably look for it.
The standalone checkboxes (protocol log, DTR/RTS) take a full row instead
of half of one, which is what was breaking the alignment.
The backend list mixed two different questions. 'Icom (USB)' and 'Icom
(network)' were separate entries; Kenwood and Elecraft hid the same
choice in a field further down; and Flex, TCI and OmniRig sat in the same
list as if they were the same kind of answer. An operator picks a radio
and then says how it is plugged in, so that is what the panel asks, in
that order, and the two answers together choose the backend.
Each brand offers only the connections it has, and a brand with one way
in still shows it, greyed: 'there is no choice here' is an answer and an
empty space is not. The stored backend names are unchanged — 'icom-net'
is still 'icom-net' — so a settings file written by an older build keeps
working, and brand+connection are DERIVED from it rather than held
alongside it, which is what keeps them from drifting apart when something
else writes the backend.
USB, RS-232-to-Ethernet, and the radio's own network protocol are three
different things, so they are three entries in one dropdown — and the
transport is now a stored setting rather than something deduced from
which field happened to be filled in. The old rule (a host wins whenever
it is not empty) is invisible from the settings page: someone who typed a
host months ago and later set a COM port had a radio that never answered
and nothing on screen to say why.
The third entry is named and refused, with the reason. It is a session
with its own framing and login, not the CAT byte stream over a socket, so
it has to be written per radio and against one — and a K4 owner reading
this list should be told that, not left wondering whether the empty
address field was the problem.
The upgrade reads an older install from what it has: a configured host
means the bridge, which is what the previous code used it for. Pinned by
a test, including the case that matters after the fact — choosing USB
with a stale host still stored gives the COM port.
The network option IS implemented — the same ASCII CAT over TCP instead
of a cable, for a ser2net bridge, an Ethernet-serial adapter, or a radio
exposing its raw CAT port. What was wrong is how it was offered: the COM
port and the network address sat side by side with nothing to say that
the address wins whenever it is not empty.
Worse, the example address read 192.168.1.50:4532. That is Hamlib
rigctld's port — a different protocol, and the one OpsLog SERVES under
'Share CAT'. Anyone copying the example was pointing the radio link at
OpsLog's own server.
Now one choice, then the fields that belong to it. And when the far end
answers something that is not the radio's CAT, the error says that rather
than 'check the baud rate', which over TCP is advice about a setting that
cannot be the cause.
F3 listed every award that existed, enabled or not, followed or not — so
a station chasing three of them assigned references from a list of twenty
and had to know which of the twenty mattered.
It now applies the same two rules the Awards tab already uses: an award
switched off in the editor is not a candidate for anything, and when a
selection of followed awards exists, only those are offered. An empty
selection still means all of them, so nobody loses a picker by never
having chosen.
A station with a switch knows something the log does not: which antenna
is actually connected. The working conditions hold what was PLANNED for
the band, and stay right until the operator throws the switch — after
which every QSO keeps claiming the other antenna.
Optional, and off by default: a station that names its antennas
differently in the two places would otherwise find its log quietly
rewritten. The name written is the one configured on the device, since
that is the name the operator gave it and the one they will look for.
WHICH PORT is the real problem, and the reason this is not a one-liner.
The switch has two, the radio has two jacks, and the QSO went out through
one of them; naming the wrong port's antenna is worse than naming the
band default, because it looks authoritative. The radio's own TX antenna
selection decides, and the jack-to-port wiring is a setting — it is the
station's cabling and neither device can report it.
When the port cannot be told — a transverter jack, a rig that reports
nothing, both switch ports live — nothing is written and the band default
stands. Silence beats a confident guess in a field nobody re-checks.
The SunSDR announces its own stream at connect —
audio_stream_sample_type:float32 and audio_stream_channels:2 — and both
were being logged as unhandled while the code worked the format out from
frame arithmetic. The declaration is better evidence and arrives before
the first frame; the arithmetic stays as the check on it. The channel
count now drives the mix-down instead of an assumed stereo.
Adds a ten-second test recording, written as a WAV beside the QSO
recordings. Counting frames proves a socket is delivering bytes; it says
nothing about whether those bytes are the receiver's audio, at the right
rate, in the right order. A stream decoded with the width wrong or the
samples misaligned counts exactly as well as a correct one and sounds
like a fan — so the test is a file the operator can play, the same way
the CW decoder was settled on the air rather than on a spectrogram.
The file is written at the rate the RADIO reported, not a constant: a
recording at the wrong rate plays at the wrong speed, which is the one
fault that would be blamed on the decoding.
Two things reported together, both about a list that fights back.
The GRID froze nothing: every spot landed at the top and pushed the rest
down, so a few rows in, the callsign under the pointer had moved by the
time the click arrived. It now stops redrawing as soon as it is scrolled
away from the top and says how many spots are waiting; reaching the top
again, or clicking the notice, releases it. The arrivals are counted by
finding the frozen top row in the live list rather than by comparing
lengths — the list is a ring buffer, so once it is full a length
comparison would report nothing new for the rest of the evening.
The COMMAND BUTTONS were capped at 120 characters. A DXSpider filter
naming the prefixes an operator wants runs well past that, and the field
just stopped accepting keystrokes: the command was saved truncated with
nothing to say why. 500 now, with the full text in the tooltip since the
box cannot show it.
A station new on this band AND in this mode is one status, 'new-band-mode',
and the badge table has an entry for neither half. The lookup returned
nothing, so those rows showed only their grid or prefix badge — and with
NEW/BAND/MODE selected, a row whose visible badges were LOC and PFX read
as the filter letting through things nobody asked for. It was not: the
row belonged there and the panel failed to say why.
catsOf has always split that status into its two categories for filtering.
The badges now do the same on screen.
Both are the same bug. ReadState returns early while transmitting — the
rig answers '?;' to IF; then, and treating that as a fault used to drop
the link — but that early return also skipped the panel update and the
meter read.
So the panel believed the radio was still receiving. Pressing MOX again
therefore sent ANOTHER transmit command instead of RX, and the K3 stayed
keyed, exactly as reported. And the power and SWR bars were only ever
read at the one moment they mean nothing.
Reading meters while transmitting needs one more guard: a '?;' then says
when the question was asked, not what the radio supports, so the
unsupported-command memory is suspended for that read. Without it, one
badly timed refusal would silence a meter for the rest of the session.
Adds RIT/XIT offset control (±10/±100 Hz, offset shown), a 4.0 kHz filter
button for FT8, and logs the K3's icon word when it changes: there is no
command for 'is the ATU in line', the reference says the switch functions
show up as icon changes, so an operator toggling the ATU while watching
the log will name the bit and the button can then light up honestly.
A SunSDR already carries its receive audio on the same WebSocket as its
commands, so a virtual audio cable and a second sound card are two pieces
of plumbing an operator installs for no reason. This is the receive half:
what the QSO recorder and the CW decoder need.
The reader now looks at the frame type. It used to ignore it and split
every frame on ';' -- harmless only for as long as no stream was ever
opened, since audio bytes would otherwise have been handed to the command
parser a hundred times a second.
NOTHING HERE IS CONFIRMED ON A RADIO. The header layout comes from the
TCI documentation, and the stream-type numbers are exactly the sort of
detail a document gets right and a memory of it does not -- so the first
forty frames of a session are logged verbatim, and a test bench in
Preferences > Audio reports the sample rate the radio chose, the frames
arriving and the peak level of the last second. 'The stream is open' and
'audio is arriving' are different claims and only the second is worth
anything to whoever tries this first.
Transmit (the voice keyer) is the other half and is deliberately absent:
it has to answer the radio's chrono packets at the right pace, and that
is worth doing once the format is settled on real hardware.
Dragging a four-pixel slider to change the power by five watts is a fussy
gesture, and the Flex and Yaesu consoles have had the wheel for a while —
an operator moving between them expects it.
React registers onWheel as PASSIVE, so preventDefault() there is ignored
and the panel scrolls under the pointer while the value changes; the
listener is attached natively instead, with the live values read through
refs. Both existing panels solved it the same way, so this is a third
copy turned into one shared component -- used by the new console only.
The other two are left alone deliberately: they work, they are in daily
use, and their styling differs in ways a merge would have to guess at.
Power steps 5 W a notch, matching the K3's own coarse step.
SWT20 was written from memory of the reference rather than from Table 7,
and 20 is not an ATU switch at all — it would have pressed something else
on a real K3. An operator read the table out for us: switch 19 is the ATU
row, TAP for a tuning cycle and HOLD for tuner in line or bypassed.
Adds the HOLD as its own ATU button, because on the radio they are two
different things: tuning is a cycle you start, bypassing is a state you
leave it in.
Power takes 0-110 W on an Elecraft, per the reference — a K3 makes a
little over its rated output — while a Kenwood keeps 200.
The list is a ring buffer that held a thousand spots, and on a busy
evening a thousand arrive in a couple of minutes. So the buffer decided
how long a spot lived, and the spot LIFETIME setting never got the chance
to expire anything: fifteen minutes meant nothing when the oldest spot
was pushed out after two.
Now settable (Preferences → Cluster, beside the lifetime, since between
them they decide the same thing), 100 to 10 000. The ceiling is a real
limit rather than a round number: every spot is matched against the
worked index and the alert rules, and is a row the cluster grid and every
open band map re-render.
Reading the cluster means running down dozens of lines, and a single
click did the whole job — QSY, mode, callsign — so every line looked at
dragged the radio with it. One stray click while reading took the
operator off the station they were working.
Looking and going are two different intentions, so they are two gestures
now. The band map is unchanged: clicking a spot there is already a
deliberate act, not a way of reading a list.
rouggy